[ { "title": "RFID Rocket", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/rfid-rocket-front.png", "backImageUrl": "images/2023/rfid-rocket-back.png", "description": "RFID Rocket, designed with 1 White always on LED and 1 Blinking Red LED.", "specialInstructions": "", "solderingInstructions": "• Solder the SMD LED's and Resistors using the single pad soldering method. \nThe Red LED goes on the tail of the rocket and is marked by Red on its packaging.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find me at the Badge Life Community and Trade or Barter to get one of these!", "rarity": "Super Rare", "timestamp": "8/19/2023 20:28:48" }, { "title": "Minibadge Community Badge", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/minibadge-community-badge-front.png", "backImageUrl": "images/2023/minibadge-community-badge-back.png", "description": "Worth 9 Badge slots? Thats up to you. This is an extremely rare 7 LED badge that you may see floating around. Will not fit in a standard slot most likely on anything other than a 10x10 board. As a result a custom badge extender will be included with each one of these that is given out.", "specialInstructions": "", "solderingInstructions": "• Assemble this badge using the single pad soldering method. LED's \"D5\" and \"D6\" share the same resistor. \n• They are the Green LED's that are marked in the package and bundled together. \n• The other SMD LED's can go on any other \"D\" Marked Location. \n• It is helpful to bend the THT LED's a little. (One slightly bent to each side.) To enable them to light up the wording better.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find me at the Badge Life community, but getting one of these won't be easy. One will be given out to the person with the most lit up minibadges worn on their person that we see at the con. (Unique trades or barter for the other remaining few.)", "rarity": "Super Rare", "timestamp": "8/19/2023 20:17:57" }, { "title": "Minibadge Village", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/minibadge-village-front.png", "backImageUrl": "images/2023/minibadge-village-back.png", "description": "An unnoficial Minibadge Village badge. This design has a unique edge cut and 4 ultra bright white LED's.", "specialInstructions": "", "solderingInstructions": "• Solder using the single pad soldering method. \n• The top two and bottom two LED's are on different resistors so this can be different colors if you so choose. \n• Included is 2 Resistors and 4 White LED's.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find me at the Badge Life Community and Trade or Barter to get one of these!", "rarity": "Super Rare", "timestamp": "8/19/2023 18:48:27" }, { "title": "Lego Spaceman Badge", "author": "Kingbob", "profilePictureUrl": "", "frontImageUrl": "images/2023/lego-spaceman-badge-front.png", "backImageUrl": "images/2023/lego-spaceman-badge-back.png", "description": "SPAAAAACESHIP!!!!! This was my first foray into minibadge design. I realized that minibadges can fit Lego shirt designs pretty well and wanted to go with one that works with a variety of colors. I have black, red, and blue badges.", "specialInstructions": "", "solderingInstructions": "• Solder LED and resistor.\n• Then solder the 4 2-pin headers.\n\n https://github.com/JonDegn/Saintcon2023-minibages/blob/main/lego-spaceman/readme.md", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me", "rarity": "Super Rare", "timestamp": "8/20/2023 22:05:53" }, { "title": "KCfox", "author": "Sh33pr0ck", "profilePictureUrl": "", "frontImageUrl": "images/2023/kcfox-front.png", "backImageUrl": "images/2023/kcfox-back.png", "description": "Lifelong fan or band wagon, who cares. Celebrate the greatness of the Kansas City Chiefs with this MiniBadge.", "specialInstructions": "", "solderingInstructions": "• Green dot/line on LED goes towards the enclosed side of D1.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me or just ask for one.", "rarity": "Super Rare", "timestamp": "8/22/2023 10:10:09" }, { "title": "McRib In Memoriam", "author": "Sh33pr0ck", "profilePictureUrl": "", "frontImageUrl": "images/2023/mcrib-in-memoriam-front.png", "backImageUrl": "images/2023/mcrib-in-memoriam-back.png", "description": "In memory of everyones favorite rib shaped patty.", "specialInstructions": "", "solderingInstructions": "• Green dot/line on LED goes towards the enclosed end of D1.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me or just ask.", "rarity": "Super Rare", "timestamp": "8/22/2023 10:22:53" }, { "title": "Lo-Pan BTiLC", "author": "Sh33pr0ck", "profilePictureUrl": "", "frontImageUrl": "images/2023/lo-pan-btilc-front.png", "backImageUrl": "images/2023/lo-pan-btilc-back.png", "description": "Glowing eye Lo-Pan from a classic 80s movie.", "specialInstructions": "", "solderingInstructions": "• Green dot/line on LED goes towards the enclosed end of D1 and D2. Add a little hot glue to the LEDs and over the eye holes on the back to direct the light for brighter results.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me or just ask for one.", "rarity": "Super Rare", "timestamp": "8/22/2023 10:30:26" }, { "title": "marvthegrate", "author": "rogu3bull3t", "profilePictureUrl": "", "frontImageUrl": "images/2023/marvthegrate-front.png", "backImageUrl": "images/2023/marvthegrate-back.png", "description": "This is just hubris. The minibadge is a copy of the avatar I use in many places. It includes a nod to a particular hobby I am known for. It includes all parts needed to build the badge as well as a jig if you are like me and don't like soldering the legs onto badges.", "specialInstructions": "", "solderingInstructions": "https://youtu.be/fbpvT5wf8p8", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come find me, likely at the scavenger hunt booth. I may make you tell a joke or do something fun to get one.", "rarity": "Rare", "timestamp": "8/25/2023 13:31:57" }, { "title": "Rollin With Rick", "author": "Z0nifer", "profilePictureUrl": "", "frontImageUrl": "images/2023/rollin-with-rick-front.png", "backImageUrl": "images/2023/rollin-with-rick-back.png", "description": "A simple blinking or solid minibadge with a fun QR code to scan.", "specialInstructions": "", "solderingInstructions": "• Solder using the single pad method. \n• Start with the LED's in the correct orientation, the green side should be inside/point to the square. \n• Then solder the resistor on (orientation does not matter). \n• Finally solder either the left or right copper pad with the center to either blink or stay solid.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come trade with me!", "rarity": "Super Rare", "timestamp": "8/25/2023 23:47:29" }, { "title": "HALLWAY TALK'S BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/hallway-talks-badge-front.png", "backImageUrl": "images/2023/hallway-talks-badge-back.png", "description": "Hallway talks were started to give insight into all the incredible effort that makes SAINTCON a success for all involved. We post videos of interviews and behind the scenes content of all things saintcon!", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Event", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find us in the hallways, and ask us for one of these neat badges... Because... We want to talk!", "rarity": "Uncommon", "timestamp": "8/26/2023 17:16:57" }, { "title": "VENT EVENT BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/vent-event-badge-front.png", "backImageUrl": "images/2023/vent-event-badge-back.png", "description": "The VENT Event allows security professionals an opportunity to speak and tell\nstories “off the record”. And collaborate to find some creative solutions to the complex problems we have in our industry.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Event", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "To get one of these MiniBadges, you will need to attend and participate in the VENT event.", "rarity": "Uncommon", "timestamp": "8/26/2023 17:27:17" }, { "title": "ID/10T COMMUNITY BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/id-10t-community-badge-front.png", "backImageUrl": "images/2023/id-10t-community-badge-back.png", "description": "Industrial Devices and IoT together make an interesting challenge you should explore.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "If you’re interested in learning about control systems and how they work, as well as discussing the security implications of these systems, come visit our community and get one of these unique badges.", "rarity": "Common", "timestamp": "8/26/2023 17:58:41" }, { "title": "ICS ESCAPE CHALLENGE - I SURVIVED BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/ics-escape-challenge-i-survived-badge-front.png", "backImageUrl": "images/2023/ics-escape-challenge-i-survived-badge-back.png", "description": "Will you be able to identify and contain cyber threats while restoring functionality to Acme’s industrial operations? Come find out in our ICS escape challenge!", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Contest", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come partcipate to get 1 of our 2 challenge badges.", "rarity": "Uncommon", "timestamp": "8/26/2023 18:40:16" }, { "title": "ICS ESCAPE CHALLENGE - I FAILED BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/ics-escape-challenge-i-failed-badge-front.png", "backImageUrl": "images/2023/ics-escape-challenge-i-failed-badge-back.png", "description": "Will you be able to identify and contain cyber threats while restoring functionality to Acme’s industrial operations? Come find out in our ICS escape challenge!", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.\n\n• D1 is the White LED\n• D2 is the Red LED", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Contest", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come partcipate to get 1 of our 2 challenge badges.", "rarity": "Uncommon", "timestamp": "8/26/2023 18:47:45" }, { "title": "SPACE COMMUNITY CUBE SAT BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/space-community-cube-sat-badge-front.png", "backImageUrl": "images/2023/space-community-cube-sat-badge-back.png", "description": "Come learn how to decode data being transmitted and attempt to send commands to the satellite and see its response on the display. We will feature a large display with real-time images of a simulated satellite orbiting the earth.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistors using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Visit our community to claim one of these badges.", "rarity": "Common", "timestamp": "8/26/2023 20:54:15" }, { "title": "TFHT - THE TRUTH IS OUT THERE...", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/tfht-the-truth-is-out-there-front.png", "backImageUrl": "images/2023/tfht-the-truth-is-out-there-back.png", "description": "There is significant evidence that the TFHT Minibadge does exist,\nand the conspiracy is not a conspiracy, we have proof that with\nthe Minibadge is actually a tracker and serves to augment all\nfields of mind control, making it the most dangerous element of\nthis supposed “security conference”.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Event", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "~REDACTED INFORMATION~", "rarity": "Uncommon", "timestamp": "8/26/2023 21:05:20" }, { "title": "LAN PARTY EVENT BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/lan-party-event-badge-front.png", "backImageUrl": "images/2023/lan-party-event-badge-back.png", "description": "Come get your LAN on, and experience this classic event. We’ll have a variety of games available, including StarCraft, Cursed Halo, Battlefield 1942, Minecraft, Overwatch 2, League of Legends, Rocket League, PayDay 2, and others.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.\n\n• These alternate with the clock once built.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Event", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come to the Event to claim one of these.", "rarity": "Rare", "timestamp": "8/26/2023 21:21:24" }, { "title": "HOMELABS COMMUNITY BADGE", "author": "bfcoder", "profilePictureUrl": "", "frontImageUrl": "images/2023/homelabs-community-badge-front.png", "backImageUrl": "images/2023/homelabs-community-badge-back.png", "description": "Derived from a SAINTCON talk in 2019, it has grown to a large following of hardware and software enthusiasts, hackers, recyclers, coders, network people, and pretty much everything in-between.", "specialInstructions": "", "solderingInstructions": "• Solder the LED as indicated in the picture, leave the lead wires long enough to\n• Bend the LED over to be in the middle of the badge.\n• Solder on the resistor\n• Solder on the header pins", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "The only requirement is that you bring yourself and your curiosity. We'll take care of the rest.", "rarity": "Common", "timestamp": "8/27/2023 6:34:49" }, { "title": "FOX HUNT CHALLENGE BADGE", "author": "bfcoder", "profilePictureUrl": "", "frontImageUrl": "images/2023/fox-hunt-challenge-badge-front.png", "backImageUrl": "images/2023/fox-hunt-challenge-badge-back.png", "description": "Beacons will be hidden throughout SAINTCON. Each Beacon resides on a frequency and will be transmitting morse code. It is up to you to find them using Ham Radio, Software Defined Radio (SDR) or other means.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Contest", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come find us and participate in the event.", "rarity": "Uncommon", "timestamp": "8/27/2023 6:45:17" }, { "title": "BLUE TEAM COMMUNITY BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/blue-team-community-badge-front.png", "backImageUrl": "images/2023/blue-team-community-badge-back.png", "description": "The Eiffel 65 Community will examine what the defensive side of security encompasses. Come peel back the layers of the defensive onion and explore the depths of defensive cyber disciplines.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Details are still being worked out, but to collect our MiniBadge, come visit our booth for more details on how get this cool MiniBadge.", "rarity": "Common", "timestamp": "8/27/2023 7:01:36" }, { "title": "EDUCATION SECURITY COMMUNITY", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/education-security-community-front.png", "backImageUrl": "images/2023/education-security-community-back.png", "description": "From the folks at UEN. Our community will focus on the security needs and collaboration that is helpful for our K12, higher education and library educational communities. Presentations, walk-ups and hands-on workshops will focus on open discussions and real-world cybersecurity experiences in the education environment.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come to one of our discussions.", "rarity": "Uncommon", "timestamp": "8/27/2023 7:10:10" }, { "title": "HEALTHCARE HACKING COMMUNITY BADGE", "author": "Brucifer", "profilePictureUrl": "", "frontImageUrl": "images/2023/healthcare-hacking-community-badge-front.png", "backImageUrl": "images/2023/healthcare-hacking-community-badge-back.png", "description": "The Health Care Hacking Community is a location for conference attendees to gather to learn and share information on the state of health care cybersecurity and how it intersects with personal health.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come visit our community and particpate!", "rarity": "Common", "timestamp": "8/27/2023 7:20:20" }, { "title": "HARDWARE HACKING COMMUNITY BADGE", "author": "rogu3bull3t", "profilePictureUrl": "", "frontImageUrl": "images/2023/hardware-hacking-community-badge-front.png", "backImageUrl": "images/2023/hardware-hacking-community-badge-back.png", "description": "The Hardware Hacking Community is back with the name you’ve known us by for years! The HHC is “The Place” to come to solder, repair, learn, and destroy electronic-based hardware.\n\nThis badge is meant to be a companion to the Beginning Soldering classes with a Portal theme.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the Filament LED. The Side with a hole in it is the Positive (Anode) side. See Image below. \n• Solder the Pin Headers to the Badge.\n\nStart with the smallest components first, the resistors, then the SMD LED. The easiest way to put the flexible LED on is to carefully bend the leads at a 90* angle, this shortens the lead and helps keep them out of the way of the headers. \n\nhttps://youtu.be/_L1SkQZLtTE", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Visit the Hardware Hacking Community table.", "rarity": "Common", "timestamp": "8/27/2023 9:00:38" }, { "title": "TAMPER EVIDENT COMMUNITY BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/tamper-evident-community-badge-front.png", "backImageUrl": "images/2023/tamper-evident-community-badge-back.png", "description": "If a container or object is “Tamper Evident” it is designed to make it obvious if someone has opened or modified it. Tamper evident seals, and devices we rely on are like any other security control, they have vulnerabilities.\n\nThe Tamper Evident community is all about bypassing these security devices without leaving any physical proof behind. This involves using heat, chemicals, brute force, and a keen eye for imperfections.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come Participate on our challenge.", "rarity": "Common", "timestamp": "8/27/2023 9:17:21" }, { "title": "F.I.B. TAMPER CHALLENGE BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/f-i-b-tamper-challenge-badge-front.png", "backImageUrl": "images/2023/f-i-b-tamper-challenge-badge-back.png", "description": "A Challenge provided by the TAMPER EVIDENT COMMUNITY. \n\nThis year, the F.I.B agency is back again and needs your help breaking into a package to alter some evidence.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Contest", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Stop by the Tamper Evident Community and sign up for either the Beginner or Advanced challenge. The objective of the game is to reach the center of the package undetected.", "rarity": "Uncommon", "timestamp": "8/27/2023 9:25:16" }, { "title": "HACK IN THE BOX BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/hack-in-the-box-badge-front.png", "backImageUrl": "images/2023/hack-in-the-box-badge-back.png", "description": "HITB is the best place to hang out after-hours during SAINTCON.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Event", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find us, hang out and discuss all things saintcon at one of our after hours events.", "rarity": "Uncommon", "timestamp": "8/27/2023 9:41:16" }, { "title": "LOCKPICK COMMUNITY BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/lockpick-community-badge-front.png", "backImageUrl": "images/2023/lockpick-community-badge-back.png", "description": "Lock Picking is a security “right of passage”. Your journey begins here!\n\nWhether you are new or experienced with lock picking, the Lock Picking Community is a must stop. This is a great skill to help you learn about physical security and that everything has vulnerabilities. We will have lock picking instructions, challenges, and plenty of practice time for you to learn and develop your skills.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering. \n• Make sure to solder the LEDS in the indicated spots on the board.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge in the 4 corners only. \n• The additional 2 center pins are for belts you earn along the way.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come and Level up in the lockpicking community. As you Level up your skills, this badge has replaceable belts that will take you thorough the lockpick belt system. See how far you can level up while your at the CON!", "rarity": "Common", "timestamp": "8/27/2023 10:04:54" }, { "title": "BRIEFS COMMUNITY BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/briefs-community-badge-front.png", "backImageUrl": "images/2023/briefs-community-badge-back.png", "description": "Every security topic you can imagine, but in ONE community.\n\nBriefs is for short presentations (5-10 minutes, hard stop at 10 minutes). If you have a cool home lab, or project at work to brag. Might not be full 30-60 minute presentation, so give it 10 minutes and share what you learned.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come to one of our sessions and let every know you have been BRIEFED on the latest.", "rarity": "Uncommon", "timestamp": "8/27/2023 10:15:14" }, { "title": "THE VAULT CONTEST BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/the-vault-contest-badge-front.png", "backImageUrl": "images/2023/the-vault-contest-badge-back.png", "description": "Welcome to the Vault, the premier physical penetration test challenge at SaintCon! If you have a knack for bypassing doors, picking locks and subverting security systems, then this is the ultimate challenge for you. The Vault offers a unique experience where participants attempt to overcome doors and safes of varying degrees of difficulty, aiming to score as many points as possible before the conference comes to a close.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Contest", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come and participate in \"THE VAULT\".", "rarity": "Common", "timestamp": "8/27/2023 10:44:28" }, { "title": "AI COMMUNITY BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/ai-community-badge-front.png", "backImageUrl": "images/2023/ai-community-badge-back.png", "description": "Come to the AI Community to get hands-on with some of the latest AI tech available including Chat GPT 4, Bard v2, and Dall-e, Midjourney, and other ground-breaking models.\n\nGet new project ideas or learn ways to potentially exploit and defend an AI system. Find out how to get started building your own AI assistant. Explore AI ethics and concerns and enjoy fun conversation on related movies, and debate which way the world will end.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.\n• D2 LED Blinks with the clock.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come and partcipate and lean about the latest in AI.", "rarity": "Common", "timestamp": "8/27/2023 10:52:34" }, { "title": "APPLICATION SECURITY COMMUNITY BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/application-security-community-badge-front.png", "backImageUrl": "images/2023/application-security-community-badge-back.png", "description": "Applications run everything, and we run the Applications. Join us!\n\nIn the Application Security Community, we will show you the importance of keeping your application code secure. We will show you how to identify, fix, and prevent vulnerabilities in your application code and secure coding practices. We will also show you how to evaluate your application security.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come join us at our booth and take on a challenge.", "rarity": "Common", "timestamp": "8/27/2023 10:59:41" }, { "title": "APPLICATION SECURITY CHALLENGE BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/application-security-challenge-badge-front.png", "backImageUrl": "images/2023/application-security-challenge-badge-back.png", "description": "Find and Fix vulnerabilities, it’s our biggest challenge.\n\nDo you have what it takes to find and fix vulnerabilities in source code? Compete against other attendees to be the first to fix all vulnerabilities in a simple python Flask web application. Clone the repo, find vulnerabilities, fix them, and submit your code to get a score. Not sure how to get started? Visit the AppSec community and learn how to use tools that will do the dirty work of finding vulnerabilities for you.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Contest", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come participate in our challenge!", "rarity": "Uncommon", "timestamp": "8/27/2023 11:15:48" }, { "title": "BADGELIFE COMMUNITY BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/badgelife-community-badge-front.png", "backImageUrl": "images/2023/badgelife-community-badge-back.png", "description": "Badgelife is the best life. Come explore this crazy world of Badges and MiniBadges", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come visit the minibadge display. Make a contribution of a COMPLETED minibadge to the display or tell us your favorite thing about minibadges to claim one.", "rarity": "Common", "timestamp": "8/27/2023 11:28:16" }, { "title": "SCAVENGER HUNT BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/scavenger-hunt-badge-front.png", "backImageUrl": "images/2023/scavenger-hunt-badge-back.png", "description": "The SAINTCON Scavenger Hunt will test your creativity and packrat tendencies by having a list of items or challenges to present to the Perpetrators for points.\n\nWe may want to see arcane technology, ancient documentation, or out and out bribes. Thinking outside of the box is not only encouraged, it’s sometimes required.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Contest", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Visit the Scavenger Hunt contest booth and locate the items list that will be posted. Play the Game, get the badge!", "rarity": "Uncommon", "timestamp": "8/27/2023 11:41:20" }, { "title": "RFID/NFC COMMUNITY BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/rfid-nfc-community-badge-front.png", "backImageUrl": "images/2023/rfid-nfc-community-badge-back.png", "description": "We will help you discover how short range wireless communication through RFID and NFC works, and how you can take advantage of it, or secure it.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come partcipate on one of our activities to claim your badge.", "rarity": "Common", "timestamp": "8/27/2023 11:49:05" }, { "title": "VALCOM SPONSOR BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/valcom-sponsor-badge-front.png", "backImageUrl": "images/2023/valcom-sponsor-badge-back.png", "description": "We could not be more excited to have VLCM back again this year and partner with us at this level. Their Minibadge design is of a rabid ferret, which is\nValcom’s Cybersecurity mascot.", "specialInstructions": "", "solderingInstructions": "• DO NOT SOLDER THESE LED's AT OVER 300 DEGREES CELSIUS OR THEY WILL MELT!\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Sponsor", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "To get one of these MiniBadges, please visit the Valcom booth in the expo center.", "rarity": "Common", "timestamp": "8/27/2023 12:49:10" }, { "title": "COMPUNET SPONSOR BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/compunet-sponsor-badge-front.png", "backImageUrl": "images/2023/compunet-sponsor-badge-back.png", "description": "Compunet is back again as one of this years amazing Sponsors.", "specialInstructions": "", "solderingInstructions": "• DO NOT SOLDER THESE LED's AT OVER 300 DEGREES CELSIUS OR THEY WILL MELT!\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Sponsor", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "You can obtain this MiniBadge by visiting the Compunet Sponsor Booth and interacting with their staff.", "rarity": "Common", "timestamp": "8/27/2023 12:58:58" }, { "title": "EOS SPONSOR BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/eos-sponsor-badge-front.png", "backImageUrl": "images/2023/eos-sponsor-badge-back.png", "description": "EOS is another one of our great sponsors this year.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Sponsor", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "You can obtain this MiniBadge by visiting the EOS Sponsor Booth and interacting with their staff.", "rarity": "Common", "timestamp": "8/27/2023 13:03:56" }, { "title": "THE KEEP COMMUNITY BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/the-keep-community-badge-front.png", "backImageUrl": "images/2023/the-keep-community-badge-back.png", "description": "Your quest begins here! Hone your hacking skills and put them to the test.\nThe Keep is a community where you can develop your hacking skills. Have you ever wanted to come to a conference, hack a machine, and walk away feeling like you own the world? Yeah, you can do that here.", "specialInstructions": "", "solderingInstructions": "• Solder the LED as indicated in the picture, leave the lead wires long enough to\nbend the LED over to be in the middle of the badge.\n• Solder on the resistor\n• Solder the 2 shorter header pins to the top of the Brick badge.\n• Solder the 2 longer header pins to the bottom of the torch and solder in place.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Visit our community and partcipate to get one of the coolest badges at SAINTCON!", "rarity": "Common", "timestamp": "8/27/2023 14:45:46" }, { "title": "Airwolf", "author": "Opie", "profilePictureUrl": "", "frontImageUrl": "images/2023/airwolf-front.jpg", "backImageUrl": "images/2023/airwolf-back.jpg", "description": "When I first saw the filament LED last year with Yoda, Airwolf immediately came to my mind. I love aviation and cars and Airwolf was one of my favorite TV shows when I was growing up.", "specialInstructions": "", "solderingInstructions": "Assembly instructions are here.\n\nhttps://tinyurl.com/bddpytpp", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me to get one of these.", "rarity": "Super Rare", "timestamp": "8/27/2023 20:48:06" }, { "title": "U of U", "author": "Professor Plum", "profilePictureUrl": "", "frontImageUrl": "images/2023/u-of-u-front.png", "backImageUrl": "images/2023/u-of-u-back.png", "description": "Show your support of the University of Utah", "specialInstructions": "", "solderingInstructions": "I believe the design was in last years mini badge book. \n• Place 0803 LED, then 0803 resister.\n• Then finally the 3 sets of 2.54mm male headers", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Just Ask for one", "rarity": "Super Rare", "timestamp": "8/29/2023 13:04:39" }, { "title": "Spy vs Spy", "author": "Professor Plum", "profilePictureUrl": "", "frontImageUrl": "images/2023/spy-vs-spy-front.png", "backImageUrl": "images/2023/spy-vs-spy-back.png", "description": "The cold war never ended. Spy vs Spy badge, One spy hold a bomb with a burning fuse, the other a ticket time bomb", "specialInstructions": "", "solderingInstructions": "• First place surface mount LED. \n• Add 2 resistors on the back.\n• Next add through hole LED, and finally add the header legs.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me", "rarity": "Uncommon", "timestamp": "8/29/2023 13:12:05" }, { "title": "miniLCD Badge", "author": "Professor Plum", "profilePictureUrl": "", "frontImageUrl": "images/2023/minilcd-badge-front.png", "backImageUrl": "images/2023/minilcd-badge-back.png", "description": "Show your love for Metroid, Pitfall, or Doom! Choose which display option to flash to the badge!", "specialInstructions": "", "solderingInstructions": "• Solder LCD, MCU, then capacitor and resistor. \n• Layout and flashing instructions at:\n\n https://github.com/Professor-plum/stm8_minibadges", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Unfortunately, do to the higher BoM costs this badge is available for $5", "rarity": "Super Rare", "timestamp": "8/29/2023 14:37:29" }, { "title": "Toy Yoda", "author": "YodaMaster", "profilePictureUrl": "", "frontImageUrl": "images/2023/toy-yoda-front.png", "backImageUrl": "images/2023/toy-yoda-back.png", "description": "This was my first attempt at a personal minibadge", "specialInstructions": "", "solderingInstructions": "• Use the single pad method to solder on the resistors and LEDs \n• LED cathode goes towards the green dot on the picture. (closed end of the U graphic on the board)\n• Solder on the 4 -2 pin headers", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find me and interact. I would like to trade but can easily be coerced into giving one up if you ask nice.", "rarity": "Uncommon", "timestamp": "8/29/2023 14:45:41" }, { "title": "Erusea Badge", "author": "Mister X", "profilePictureUrl": "", "frontImageUrl": "images/2023/erusea-badge-front.png", "backImageUrl": "images/2023/erusea-badge-back.png", "description": "The emblem of the Kingdom of Erusea from the game Ace Combat 7, one of my favorites. This will be a part of the Ace Combat minibadge set.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED Direction indicators are on the image to the left.\n• Solder the two LEDs first, using the single-pad method for hand soldering.\n• Solder the two Resistors using the same single-pad method for hand soldering.\n• Solder the 4x 2-Position headers, with the Erusea emblem facing out.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "To get this minibadge, ask me for the set and/or tell me your favorite airplane, and I'll gladly give you one.", "rarity": "Super Rare", "timestamp": "8/29/2023 20:06:38" }, { "title": "Osea Badge", "author": "Mister X", "profilePictureUrl": "", "frontImageUrl": "images/2023/osea-badge-front.png", "backImageUrl": "images/2023/osea-badge-back.png", "description": "This is the emblem of Osea from the game Ace Combat 7, one of my favorite games. This will come as a set in the Ace Combat series I'm running.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED Direction indicators are on the image to the left.\n• Solder the two LEDs first, using the single-pad method for hand soldering.\n• Solder the two Resistors using the same single-pad method for hand soldering.\n• Solder the 4x 2-Position headers, with the Osea emblem facing out.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "To get this badge, ask for one and/or tell me your favorite airplane, and I'll happily give you one.", "rarity": "Super Rare", "timestamp": "8/29/2023 21:43:06" }, { "title": "MLG Badge (Dark Mode)", "author": "Mister X", "profilePictureUrl": "", "frontImageUrl": "images/2023/mlg-badge-dark-mode-front.png", "backImageUrl": "images/2023/mlg-badge-dark-mode-back.png", "description": "Coming from one of the more iconic parts of internet meme, the 8-bit glasses can be recognized almost immediately. This badge comes with white glasses on a black background.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED Direction indicators are on the image to the left.\n• Solder the two LEDs first, using the single-pad method for hand soldering.\n• Solder the Resistor using the same single-pad method for hand soldering.\n• Solder the 4x 2-Position headers, with the 8-bit glasses artwork facing out.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Because there is a light mode and dark mode version of this badge, specify which one you would like.", "rarity": "Super Rare", "timestamp": "8/29/2023 21:55:20" }, { "title": "Jordan District", "author": "Opie", "profilePictureUrl": "", "frontImageUrl": "images/2023/jordan-district-front.jpg", "backImageUrl": "images/2023/jordan-district-back.jpg", "description": "This is my first ever minibadge I designed.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Just ask for one", "rarity": "Rare", "timestamp": "8/29/2023 23:16:04" }, { "title": "Top Gun Inverted", "author": "Opie", "profilePictureUrl": "", "frontImageUrl": "images/2023/top-gun-inverted-front.jpg", "backImageUrl": "images/2023/top-gun-inverted-back.jpg", "description": "Top Gun is my favorite movie and I designed a badge from one of the scenes in the movie", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Just ask for one.", "rarity": "Rare", "timestamp": "8/29/2023 23:26:11" }, { "title": "MLG Badge (Light Mode)", "author": "Mister X", "profilePictureUrl": "", "frontImageUrl": "images/2023/mlg-badge-light-mode-front.png", "backImageUrl": "images/2023/mlg-badge-light-mode-back.png", "description": "Coming from one of the more iconic parts of internet meme, the 8-bit glasses can be recognized almost immediately. This badge comes with black glasses on a white background.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED Direction indicators are on the image to the left.\n• Solder the two LEDs first, using the single-pad method for hand soldering.\n• Solder the Resistor using the same single-pad method for hand soldering.\n• Solder the 4x 2-Position headers, with the 8-bit glasses artwork facing out.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Because there are two versions of this badge, specify which one you would like.", "rarity": "Super Rare", "timestamp": "8/30/2023 7:18:09" }, { "title": "Pardon My French", "author": "Sh33pr0ck", "profilePictureUrl": "", "frontImageUrl": "images/2023/pardon-my-french-front.png", "backImageUrl": "images/2023/pardon-my-french-back.png", "description": "In honor of knocking the lab from the #1 spot in 2023. The absolute quirkiest, strange, and lovable dog out there.", "specialInstructions": "", "solderingInstructions": "Green dot/line on the LED goes towards the enclosed side of D1. Solder jumper for either blinking or solid.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Ask how you can follow my beloved Frenchie on social...or just ask for one.", "rarity": "Super Rare", "timestamp": "9/1/2023 9:27:06" }, { "title": "Ash vs. Minibadge", "author": "Sh33pr0ck", "profilePictureUrl": "", "frontImageUrl": "images/2023/ash-vs-minibadge-front.png", "backImageUrl": "images/2023/ash-vs-minibadge-back.png", "description": "The master of comedic horror brought us a classic in the 90s. This MiniBadge plays some of the best one liners from Army of Darkness using a W25Q32 and an ATTiny85. Hail to the King Baby!", "specialInstructions": "", "solderingInstructions": "Instructions will be include with badge.", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me.", "rarity": "Super Rare", "timestamp": "9/1/2023 9:44:00" }, { "title": "Mister X Badge", "author": "Mister X", "profilePictureUrl": "", "frontImageUrl": "images/2023/mister-x-badge-front.png", "backImageUrl": "images/2023/mister-x-badge-back.png", "description": "This is my first year designing minibadges, and this is the first minibadge I designed. This features my emblem on a blue background. Quick thanks to r0gu3bull3t for the help!", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED Direction indicators are on the image to the left.\n• Solder the two LEDs first, using the single-pad method for hand soldering.\n• Solder the Resistor using the same single-pad method for hand soldering.\n• Solder the 4x 2-Position headers, with the Mister X emblem facing out.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find me walking around and talk with me, and I'll be happy to give you one. I'll have a jacket with the emblem to make me easier to spot.", "rarity": "Super Rare", "timestamp": "9/1/2023 14:12:15" }, { "title": "Hylian Shield", "author": "bfcoder", "profilePictureUrl": "", "frontImageUrl": "images/2023/hylian-shield-front.png", "backImageUrl": "images/2023/hylian-shield-back.png", "description": "Glowing Hylian Shield. Use hot glue for best results. There is a single LED on the back. If you make a shield of hot glue on the back, it will light up very nicely!", "specialInstructions": "", "solderingInstructions": "Starting on the back, solder on the resistor at the top. Next solder on the LED in the middle. The left side is the positive side. You can faintly see a + symbol on the left border and a - symbol on the right border. Flip it over so you can see the silver shield and solder the header pins in place.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me! Or buy it.", "rarity": "Uncommon", "timestamp": "9/3/2023 18:10:06" }, { "title": "CareBear", "author": "CareBear", "profilePictureUrl": "", "frontImageUrl": "images/2023/carebear-front.png", "backImageUrl": "images/2023/carebear-back.png", "description": "This is a modern version of the Rainbow Care Bear. It features a copper image tracing with a slow 3mm RGB led.", "specialInstructions": "", "solderingInstructions": "Solder using the single pad soldering method. This will come with a slow 3mm rgb led and one resistor.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade or barter", "rarity": "Super Rare", "timestamp": "9/4/2023 14:11:49" }, { "title": "Hotline Miami", "author": "Moomoo", "profilePictureUrl": "", "frontImageUrl": "images/2023/hotline-miami-front.png", "backImageUrl": "images/2023/hotline-miami-back.png", "description": "Inspired by Hotline Miami and I used their main page graphic. This is the main title screen badge for my Hotline Miami series.", "specialInstructions": "", "solderingInstructions": "Solder using the single pad soldering method. This will come with a red smd led, blue smd led, and their associated resistors.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade, barter, ask", "rarity": "Super Rare", "timestamp": "9/4/2023 14:19:08" }, { "title": "Jigsaw", "author": "Moomoo", "profilePictureUrl": "", "frontImageUrl": "images/2023/jigsaw-front.png", "backImageUrl": "images/2023/jigsaw-back.png", "description": "This is a pixelated version of Jigsaw. This features see through eyes, mouth, cheek swirls, and bowtie. These see through portions will allow red leds to illuminate them giving jigsaw his iconic look.", "specialInstructions": "", "solderingInstructions": "Solder using the single pad soldering method. This will come with 2 red leds and their associated resistor. Each led has its own resistor and can be changed to any other color as long as you have the correct resistor for the color.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade or ask", "rarity": "Super Rare", "timestamp": "9/4/2023 14:25:10" }, { "title": "Hotline Miami - Rasmus", "author": "Moomoo", "profilePictureUrl": "", "frontImageUrl": "images/2023/hotline-miami-rasmus-front.png", "backImageUrl": "images/2023/hotline-miami-rasmus-back.png", "description": "Rasmus is the owl mask character from Hotline Miami. This is part of my Hotline Miami collection. This features an 8bit graphic with a see-through background so it glows orange and red.", "specialInstructions": "", "solderingInstructions": "Solder using the single pad soldering method. This will come with a red smd led, orange smd led, and their associated resistor.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade or ask", "rarity": "Super Rare", "timestamp": "9/4/2023 14:35:56" }, { "title": "FMA Human Transmutation Circle", "author": "Moomoo", "profilePictureUrl": "", "frontImageUrl": "images/2023/fma-human-transmutation-circle-front.png", "backImageUrl": "images/2023/fma-human-transmutation-circle-back.png", "description": "This is the human transmutation circle from Full Metal Alchemist that was used in an attempt to bring their late mother back to life using alchemy. This badge will glow blue through the circle.", "specialInstructions": "", "solderingInstructions": "Solder using the single pad soldering method. This will come with a blue led and resistor.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade or ask", "rarity": "Super Rare", "timestamp": "9/4/2023 14:50:03" }, { "title": "Hotline Miami - Richard", "author": "Moomoo", "profilePictureUrl": "", "frontImageUrl": "images/2023/hotline-miami-richard-front.png", "backImageUrl": "images/2023/hotline-miami-richard-back.png", "description": "This is the 8bit Richard mask from Hotline Miami. This is part of my Hotline Miami series. This features a red glow to give the mask its iconic look.", "specialInstructions": "", "solderingInstructions": "Solder using the single pad soldering method. This will come with two red leds and two resistors. You can change out the leds and resistors as they are on their own circuits.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade or ask", "rarity": "Super Rare", "timestamp": "9/4/2023 14:53:16" }, { "title": "FMA Alkahestric Reverse", "author": "Moomoo", "profilePictureUrl": "", "frontImageUrl": "images/2023/fma-alkahestric-reverse-front.png", "backImageUrl": "images/2023/fma-alkahestric-reverse-back.png", "description": "This is the Alkahestric Reverse circle from Full Metal Alchemist. In the story, this was used to reverse a nation-wide transmutation circle that turned people into a philosopher's stone. This badge will have a blue led that illuminates the circle.", "specialInstructions": "", "solderingInstructions": "Solder using the single pad soldering method. This will come with a blue led and resistor.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade or ask", "rarity": "Super Rare", "timestamp": "9/4/2023 14:57:45" }, { "title": "Sauron - Black Speech", "author": "Moomoo", "profilePictureUrl": "", "frontImageUrl": "images/2023/sauron-black-speech-front.png", "backImageUrl": "images/2023/sauron-black-speech-back.png", "description": "This features the mask and eye of Sauron surrounded by the Black Speech written on the One Ring in Elvish Tengwar script. Ash nazg durbatulûk, ash nazg gimbatul,\nash nazg thrakatulûk agh burzum-ishi krimpatul.\n\nThis badge has clear portions for the mask, inner portions of the script, and center of the eye. These portions will glow red and orange from the leds on the back.", "specialInstructions": "", "solderingInstructions": "Solder using the single pad soldering method. This will come with a red led, and orange led, and their accompanying resistors. Each led and resistor are on their own circuit and can be changed out for any color if you have the correct resistor for that color.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade or ask", "rarity": "Super Rare", "timestamp": "9/4/2023 15:23:46" }, { "title": "Utah Valley University", "author": "FiberHands (Bobby Carbine)", "profilePictureUrl": "", "frontImageUrl": "images/2023/utah-valley-university-front.png", "backImageUrl": "images/2023/utah-valley-university-back.png", "description": "This badge was designed by Bobby Carbine, a UVU employee.", "specialInstructions": "", "solderingInstructions": "This is a pretty simple design with a surface mount LED and resistor on the back.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Ask for one from a UVU employee", "rarity": "Rare", "timestamp": "9/4/2023 16:26:43" }, { "title": "Nativity", "author": "kfeuz", "profilePictureUrl": "", "frontImageUrl": "images/2023/nativity-front.png", "backImageUrl": "images/2023/nativity-back.png", "description": "A simple nativity scene to remind myself and others about one of the most important events in history and one of my favorite times of the year", "specialInstructions": "", "solderingInstructions": "The resistor goes in the in R1 spot in any orientation. The led goes in the d1 spot with the green mark towards the silkscreen rectangle marking. I recommend mounting the led upside down (i.e. so the led is shining into and through the translucent star). It still lights up well if you just mount the led in its normal orientation as well.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me or come share a story", "rarity": "Super Rare", "timestamp": "9/5/2023 11:18:52" }, { "title": "Tamagotchis", "author": "r0gu3bull3t", "profilePictureUrl": "", "frontImageUrl": "images/2023/tamagotchis-front.png", "backImageUrl": "images/2023/tamagotchis-back.png", "description": "I thought it would be fun to have Tamagotchis that won't die! There are 4 versions (Tama1, Tama2, Tama3, & Tama4), one for each day of the con.", "specialInstructions": "", "solderingInstructions": "https://youtu.be/P67NellaeM0", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Ask r0gu3bull3t for one, bonus points if you have a badge to trade. She can usually be found around the soldering tables.", "rarity": "Super Rare", "timestamp": "9/6/2023 17:58:43" }, { "title": "AgReserves", "author": "AgReserves", "profilePictureUrl": "", "frontImageUrl": "images/2023/agreserves-front.png", "backImageUrl": "images/2023/agreserves-back.png", "description": "The SOC team at AgReserves wanted to put together a simple badge to share.", "specialInstructions": "", "solderingInstructions": "https://youtu.be/ydpDBeJi5oQ", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Talk to Cody Burgess, Rachel Webb, or Katie Lunceford", "rarity": "Rare", "timestamp": "9/6/2023 18:04:13" }, { "title": "Waldo Wildcat Hacker", "author": "kfeuz", "profilePictureUrl": "", "frontImageUrl": "images/2023/waldo-wildcat-hacker-front.jpg", "backImageUrl": "images/2023/waldo-wildcat-hacker-back.jpg", "description": "This is a tribute to Weber State and specifically their cybersecurity program. Even Waldo the Wildcat wants to learn offensive and defensive hacking skills.", "specialInstructions": "", "solderingInstructions": "R1 gets the 470 ohm resistor, orientation does not matter. D1 gets the white led. The little green triangle on the back of the led should point towards the resistor. I recommend mounting this led upside down so that the led is shining into (and through) the back of the board out through the front.\nR2 gets the 10 ohm resistor, again orientation does not matter. D2 gets the purple led. The green mark (looks like a T) should have the bottom of the T pointing towards the resistor. I recommend mounting this led right side up so that the led shines onto the back of the reflecting minibadge holder.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade, Come talk with me.", "rarity": "Super Rare", "timestamp": "9/7/2023 23:28:14" }, { "title": "UltraViolet SPONSOR BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/ultraviolet-sponsor-badge-front.png", "backImageUrl": "images/2023/ultraviolet-sponsor-badge-back.png", "description": "UltraViolet is one of our newest sponsors.", "specialInstructions": "", "solderingInstructions": "• Solder the LED as indicated in the picture, leave the lead wires long enough to\n bend the LED over to be in the middle of the badge.\n• Solder on the resistor\n• Solder on the header pins", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Sponsor", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Get one of our unique badges by visiting our booth in the vendor area.", "rarity": "Common", "timestamp": "9/8/2023 15:45:16" }, { "title": "AXONIUS SPONSOR BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/axonius-sponsor-badge-front.png", "backImageUrl": "images/2023/axonius-sponsor-badge-back.png", "description": "AXONIUS is another one of our amazing sponsors for this year.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.\n• Solder the Jumper at the bottom of the board to contact 2 pads.\n(The pads you solder on the bottom will either make the lights on the badge blink or be solid on.)", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Sponsor", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Visit their booth to get one!", "rarity": "Common", "timestamp": "9/8/2023 17:20:09" }, { "title": "SAINTCON GOLF CLUB MINIBADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/saintcon-golf-club-minibadge-front.png", "backImageUrl": "images/2023/saintcon-golf-club-minibadge-back.png", "description": "Saintcon mini-golf? Yeah, thats a thing this year! We have set up a mini golf couse right in the conference area. Come connect, chat and hangout on the putting green!", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Event", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come play a round of golf on our mini-golf course!", "rarity": "Uncommon", "timestamp": "9/8/2023 17:42:22" }, { "title": "BRIEFS SPEAKER MINIBADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/briefs-speaker-minibadge-front.png", "backImageUrl": "images/2023/briefs-speaker-minibadge-back.png", "description": "Come share the cool things you’ve tried. Maybe it turned out just like you hoped, maybe it crashed and burned. Either way you learned something. Share it with the rest of us!", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Presenting at one of our 5-10 minutes blocks is all it takes to get one of these!", "rarity": "Rare", "timestamp": "9/8/2023 19:56:32" }, { "title": "PPG - Blossom", "author": "odie", "profilePictureUrl": "", "frontImageUrl": "images/2023/ppg-blossom-front.png", "backImageUrl": "images/2023/ppg-blossom-back.png", "description": "For when you need help saving the world before bedtime, give the Powerpuff Girls a call. First up we have Blossom, commander and the leader.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find odie in the expo hall (generally in the Lockpick Community) and trade with me.", "rarity": "Rare", "timestamp": "9/13/2023 11:44:21" }, { "title": "PPG - Bubbles", "author": "odie", "profilePictureUrl": "", "frontImageUrl": "images/2023/ppg-bubbles-front.png", "backImageUrl": "images/2023/ppg-bubbles-back.png", "description": "For when you need help saving the world before bedtime, give the Powerpuff Girls a call. Next is Bubbles, she is the joy and the laughter.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find odie in the expo hall (generally in the Lockpick Community) and trade with me.", "rarity": "Rare", "timestamp": "9/13/2023 11:47:20" }, { "title": "PPG - Buttercup", "author": "odie", "profilePictureUrl": "", "frontImageUrl": "images/2023/ppg-buttercup-front.png", "backImageUrl": "images/2023/ppg-buttercup-back.png", "description": "For when you need help saving the world before bedtime, give the Powerpuff Girls a call. Finally we have Buttercup, she is the toughest fighter.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find odie in the expo hall (generally in the Lockpick Community) and trade with me.", "rarity": "Rare", "timestamp": "9/13/2023 11:49:27" }, { "title": "The odie Badge", "author": "odie", "profilePictureUrl": "", "frontImageUrl": "images/2023/the-odie-badge-front.png", "backImageUrl": "images/2023/the-odie-badge-back.png", "description": "It's me, odie, in MiniBadge form.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "This will be a super rare badge - reserved for those near and dear to me.", "rarity": "Super Rare", "timestamp": "9/13/2023 11:55:39" }, { "title": "Owl Hoo Hack", "author": "DistinctM1nd", "profilePictureUrl": "", "frontImageUrl": "images/2023/owl-hoo-hack-front.png", "backImageUrl": "images/2023/owl-hoo-hack-back.png", "description": "After you assemble this badge (or maybe before but what fun is that?), you'll find a hidden message to decode.", "specialInstructions": "", "solderingInstructions": "• Before starting, determine where the numbers that light up are located. You can do this by shining a light through the board. This gives away the code, however, you want to make sure that you don't get solder or damage the solder mask around these numbers. \n• Begin on the Back side first. \n• LED Direction indicators are on the image above. Double check LED orientation before soldering them. \n• Solder the LEDs (labeled D1, D2, D3, D4, and D5). All of the LEDs are green. \n• Solder the resistors (Labeled R1, R2, R3, R4, R5). The resistors are all 15 ohm. \n• Solder the four 2-Pin headers to the corners.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me, attend my talk, or convince me to give you one.", "rarity": "Super Rare", "timestamp": "9/15/2023 14:32:19" }, { "title": "GhostBusters", "author": "Opie", "profilePictureUrl": "", "frontImageUrl": "images/2023/ghostbusters-front.jpg", "backImageUrl": "images/2023/ghostbusters-back.jpg", "description": "I was watching Ghost Busters one night and I though that this would be a cool looking minibadge", "specialInstructions": "", "solderingInstructions": "Begin on the back first.\nSolder the 3 LED's and 1 Resistor using the single pad method for hand soldering.\nSolder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me, or come and find me while they last.", "rarity": "Rare", "timestamp": "9/16/2023 0:17:42" }, { "title": "Delicate Arch badge", "author": "Kingbob", "profilePictureUrl": "", "frontImageUrl": "images/2023/delicate-arch-badge-front.png", "backImageUrl": "images/2023/delicate-arch-badge-back.png", "description": "This was an experiment with layering multiple PCBs in a single badge. Doing a silhouette seemed like a good choice for having multiple layers. I also tried to create a gradient background by having the solder mask fade away on the backside letting though various amounts of light to emulate a sunset. I chose delicate arch on a Utah-shaped badge because I love Arches National Park.", "specialInstructions": "", "solderingInstructions": "- Solder LED and resistor on the back of the Utah badge. The cathode (green part) of the LED should be towards the left indicated by the small dot.\n- Solder the headers to the Utah badge. Use VERY LITTLE solder on the bottom headers. Try to prevent the solder from mounding up beyond the surface of the badge. \n- Solder the arch silhouette directly on top of the bottom headers so the the side that says \"backside\" is against the Utah badge.\n\nhttps://github.com/JonDegn/Saintcon2023-minibages/blob/main/delicate-arch/readme.md", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me", "rarity": "Super Rare", "timestamp": "9/17/2023 21:56:29" }, { "title": "Inifinity Mirror Badge", "author": "Kingbob", "profilePictureUrl": "", "frontImageUrl": "images/2023/inifinity-mirror-badge-front.jpg", "backImageUrl": "images/2023/inifinity-mirror-badge-back.jpg", "description": "I started working on the designs for this badge shortly after Saintcon 2022. It's taken 4 or so iterations to get into it's current state. This badge has 5 PCBs, a 3D-printed frame, and more than 20 different pieces. It's going to take some patience to assemble this guy. It also comes with a 3D-printed jig to help with assembly. You will need some super glue and some side cutters and/or a metal file to assemble this.", "specialInstructions": "", "solderingInstructions": "See https://github.com/JonDegn/Saintcon2023-minibages/blob/main/infinity-mirror/readme.md", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "$20 or trade something cool", "rarity": "Super Rare", "timestamp": "9/17/2023 22:50:31" }, { "title": "Black Widow", "author": "j3tt", "profilePictureUrl": "", "frontImageUrl": "images/2023/black-widow-front.png", "backImageUrl": "images/2023/black-widow-back.png", "description": "Black Widow is my very first mini badge creation.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LED first, using the single-pad method for hand soldering.\n• Solder the Resistor using the same single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come find me - willing to give out or trade!", "rarity": "Super Rare", "timestamp": "9/18/2023 19:59:05" }, { "title": "Brucifer 2023", "author": "Brucifer", "profilePictureUrl": "", "frontImageUrl": "images/2023/brucifer-2023-front.png", "backImageUrl": "images/2023/brucifer-2023-back.png", "description": "This MiniBadge displays a representation of Brucifer's favorite animal, the rare horned heterochromian winking tapir. The winking effect is created with a RC Delay circuit - using the CLK pin, 2 capacitors in parallel, and a resistor to delay the lighting of the second LED.", "specialInstructions": "", "solderingInstructions": "- Solder the R1 (10 ohm, labelled \"100\") and R2 (68 ohm, labelled \"680\") resistors first, using the single-pad method for hand soldering.\n- Solder the D1 blue LED, with the cathode toward the top of the mini-badge, using the single-pad method for hand soldering.\n- Solder the D2 red LED, with the cathode toward the top of the mini-badge, using the single-pad method for hand soldering.\n- Solder the C1 and C2 tantalum capacitors, with the positive end (marked with the brown line) to the left\n- Solder the 4x 2-Position headers", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me, or social engineer one from me.", "rarity": "Super Rare", "timestamp": "9/19/2023 0:50:38" }, { "title": "Energizing Life", "author": "Steve from Dixie Power", "profilePictureUrl": "", "frontImageUrl": "images/2023/energizing-life-front.png", "backImageUrl": "images/2023/energizing-life-back.png", "description": "Dixie Power has been attending SaintCon for several years and is a strong supporter of the cybersecurity community. This year, we decided to create our own badge that represents our company's field, which is an electric cooperative providing safe, reliable electric utility services in St. George, Utah.", "specialInstructions": "", "solderingInstructions": "The blue LED goes to the left of the \"D\" and the white LED goes below the clouds. The back of the badge is labeled with where the LEDs and resistors should be placed, with \"R\" representing resistor and \"D\" representing diodes or LEDs. On the back of the LED, you will see a green arrow. That arrow points to the negative side or the box with the missing side. There is also a JP1 solder pad. If you solder the left and center pads together, the LEDs will blink. If you solder the right and center together, the LEDs will be solid. When soldering the header pins to the mini badge, it is recommended to take the four header pins, place them in the mini badge slot on your powered-off main badge, and place your mini badge onto the pins. This will align the pins, making it easier to solder them on.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Look for a Dixie Power employee and trade with them.", "rarity": "Super Rare", "timestamp": "9/19/2023 14:43:21" }, { "title": "SAO Adapter", "author": "Brucifer", "profilePictureUrl": "", "frontImageUrl": "images/2023/sao-adapter-front.png", "backImageUrl": "images/2023/sao-adapter-back.png", "description": "This MiniBadge is an adapter that allows you to plug DEFCON SAO v1.69bis compatible SAOs into the SAINTCON badge. It only supports the 3V3, GND, SDA, and SCL pins. Without modification, it will not support the GPIO1 and GPIO2 pins.", "specialInstructions": "", "solderingInstructions": "- Insert the 2x3 pin header through the holes on the front of the badge, aligning the position key toward the top, matching the header outline on the front of the badge\n- Solder the 2x3 pin header pins on the back side of the badge\n- Solder the 8-position headers", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Badge Accessory", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find me and show me the SAO you want to display", "rarity": "Super Rare", "timestamp": "9/20/2023 0:22:42" }, { "title": "B3rjmp Badge", "author": "B3rJmp", "profilePictureUrl": "", "frontImageUrl": "images/2023/b3rjmp-badge-front.png", "backImageUrl": "images/2023/b3rjmp-badge-back.png", "description": "When I started school, I set my slack profile pic to a bear falling out of a tree onto a trampoline. It was taken at just the right time to make the bear look like it was jumping on the trampoline, so I figured I'd make a badge to commemorate my start into infosec.", "specialInstructions": "", "solderingInstructions": "•\tStart on the back of the pcb\n•\tSolder the resistors first, since they’re smaller it might take more time to put them on, and it’s easier without the LED’s getting in the way\n•\tSolder the LED’s next, with the green dot on the beveled side of the marking\n•\tSolder the header pins", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Look for NFC stickers with the logo on them", "rarity": "Super Rare", "timestamp": "9/23/2023 19:56:53" }, { "title": "Ensign college", "author": "Hollyhacker", "profilePictureUrl": "", "frontImageUrl": "images/2023/ensign-college-front.jpg", "backImageUrl": "images/2023/ensign-college-back.jpg", "description": "I am an adjunct professor at Ensign college and one of the ways I choose to show my passion for that is by making a minibadge for it.", "specialInstructions": "", "solderingInstructions": "There is a single resistor for this minibadge, it is small but can be soldered in either orientation. The LED is mounted with the \"green mark\" going towards the negative sign. The green mark should go into the \"garage\" or the 3 sided rectangle. You can find an assembly video at https://bit.ly/48t5MS5 .", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Social Engineer Me (just asking is a good start), Trade with me", "rarity": "Rare", "timestamp": "9/24/2023 12:24:44" }, { "title": "Trend Micro 2023", "author": "Trend Micro 2023", "profilePictureUrl": "", "frontImageUrl": "images/2023/trend-micro-2023-front.jpg", "backImageUrl": "images/2023/trend-micro-2023-back.jpg", "description": "There is a single resistor for this minibadge, it is small but can be soldered in either orientation. The LED is mounted with the \"green mark\" face so it will go into the \"garage\" or the 3 sided rectangle. You can find an assembly video at https://bit.ly/48t5MS5 .\nThe badge has 2 LED's and functions on the \"clock standard\" so it will alternate the lights", "specialInstructions": "", "solderingInstructions": "The LED is mounted with the \"green mark\" face so it will go into the \"garage\" or the 3 sided rectangle. They will go into the D1 and D2 labels. Resistor goes into the spot labeled R1. The resistors do not require a specific orientation . The \"top side\" that has the number on it is what should be showing when you solder it to the board. \n\nYou can find an assembly video at https://bit.ly/48t5MS5", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Sponsor", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trend Micro has a sponsorship booth at Saintcon this year. You can obtain this badge by visiting their booth and interacting with any of their staff.", "rarity": "Rare", "timestamp": "9/24/2023 12:37:30" }, { "title": "Tie Minibadge Extender for the Dignified Enthusiast", "author": "Hollyhacker & SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/tie-minibadge-extender-for-the-dignified-enthusiast-front.jpg", "backImageUrl": "images/2023/tie-minibadge-extender-for-the-dignified-enthusiast-back.jpg", "description": "This is a minibadge extender for displaying additional minbadges from your conference badge. This meets the \"extender standard\" and should work with the last few years of badges and the new badge for 2023. This extender will allow you to display 8 additional minibadges. This supports the clock standard. (The use of this extender will accelerate the battery consumption from whatever your powering with) . This single extender design cannot be combined with another extender if it is first in line. This extender comes with all the parts needed: Cable, headers, 20P connector, and board.", "specialInstructions": "", "solderingInstructions": "This extender is assembled in a very similar if not exactly similar to the primary badge components that are done each year. I have also made a video demonstrating key considerations for assembly. https://bit.ly/48t5MS5", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Badge Accessory", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Look these up in the Saintcon Classifieds on the badgelife page for current cost and inventory. \n\n If your SAINTCON committee just show me your badge and your wish shall be granted.", "rarity": "Super Rare", "timestamp": "9/24/2023 12:55:10" }, { "title": "Black Utah License plate customized with your handle", "author": "klipper & v0rtex", "profilePictureUrl": "", "frontImageUrl": "images/2023/black-utah-license-plate-customized-with-your-handle-front.jpg", "backImageUrl": "images/2023/black-utah-license-plate-customized-with-your-handle-back.jpg", "description": "This is the new black Utah license plate that has been gaining in popularity. A single right angle led shines down to illuminate the plate like on a real car. The cool part about it is we are going to have label makers with it to customize it with your handle! 7 letters max like a real plate. When trading with us, make sure you let us know what you want on it...otherwise you're getting a generic one of whatever we have in our pocket at the time. :D", "specialInstructions": "", "solderingInstructions": "Follow the silkscreen for the right-angle LED on the front, and the resistor on the back.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come trade with @klipper or @v0rtex", "rarity": "Uncommon", "timestamp": "9/24/2023 14:31:41" }, { "title": "Cowboy Bebop", "author": "TACOCAT", "profilePictureUrl": "", "frontImageUrl": "images/2023/cowboy-bebop-front.png", "backImageUrl": "images/2023/cowboy-bebop-back.png", "description": "Decided to make a minibadge based off of one of my favorite tv shows. If you haven't seen it you're missing out.", "specialInstructions": "", "solderingInstructions": "The side of the LED with a green line or dot goes on the side without an opening on the back of the board. Attach the LED and at D1 and resistor at R1 and you should be good to go!", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me", "rarity": "Rare", "timestamp": "9/24/2023 21:09:53" }, { "title": "The Troll Badge", "author": "TheTrollGod", "profilePictureUrl": "", "frontImageUrl": "images/2023/the-troll-badge-front.png", "backImageUrl": "images/2023/the-troll-badge-back.png", "description": "This is TheTrollGod's Personal badge.", "specialInstructions": "", "solderingInstructions": "Line up the LED with the led square. Resistors are bi-directional.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come find TheTrollGod during the conference and tell him \"I came from under the bridge\". Make sure you brush up on some pop culture and security triva!", "rarity": "Rare", "timestamp": "9/25/2023 15:49:25" }, { "title": "SAINTCON STORE MINIBADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/saintcon-store-minibadge-front.png", "backImageUrl": "images/2023/saintcon-store-minibadge-back.png", "description": "The Saintcon store is an official staple of the con. The store grows every year with more and more amazing products and sponsored products from some of the best in the business.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.\n• Solder 2 of the 3 jumper pads on the badge to either make the leds blink or be solid on.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Event", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Free with purchase while supplies last!", "rarity": "Common", "timestamp": "9/25/2023 21:25:00" }, { "title": "Zaam", "author": "Banzaam", "profilePictureUrl": "", "frontImageUrl": "images/2023/zaam-front.png", "backImageUrl": "images/2023/zaam-back.png", "description": "A simple ball of lightning", "specialInstructions": "", "solderingInstructions": "Normal solder point resistor, bulb LED solder so the bulb shines through the middle of the badge.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me", "rarity": "Super Rare", "timestamp": "9/26/2023 12:04:51" }, { "title": "NRGCIC", "author": "Banzaam", "profilePictureUrl": "", "frontImageUrl": "images/2023/nrgcic-front.png", "backImageUrl": "images/2023/nrgcic-back.png", "description": "A badge created for teams at NRG and Vivint. The image is a combination of logos.", "specialInstructions": "", "solderingInstructions": "Normal solder point resistor, bulb LED to surface solder points.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trading with various Vivint/NRG Employees", "rarity": "Rare", "timestamp": "9/26/2023 12:08:29" }, { "title": "CISA Minibadge", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/cisa-minibadge-front.png", "backImageUrl": "images/2023/cisa-minibadge-back.png", "description": "CISA is the operational lead for federal cybersecurity and the national coordinator for critical infrastructure security and resilience. We are designed for collaboration and partnership. Learn about our layered mission to reduce risk to the nation’s cyber and physical infrastructure.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Other", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find one of the CISA folks and ask them for one!", "rarity": "Uncommon", "timestamp": "9/26/2023 20:51:56" }, { "title": "SIAC MINIBADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/siac-minibadge-front.png", "backImageUrl": "images/2023/siac-minibadge-back.png", "description": "The Utah Statewide Information and Analysis Center (SIAC) is one of 80 fusion centers located throughout the U.S. that collaborates with local and federal public safety partners to create information-sharing networks. The SIAC, like other fusion centers, works as an integral conduit to the United States intelligence community.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Other", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find one of the great SIAC folks and ask for one.", "rarity": "Uncommon", "timestamp": "9/26/2023 21:00:23" }, { "title": "EDUROAM MINIBADGE", "author": "EDU-ROMEO", "profilePictureUrl": "", "frontImageUrl": "images/2023/eduroam-minibadge-front.png", "backImageUrl": "images/2023/eduroam-minibadge-back.png", "description": "Eduroam allows students, researchers, teachers and staff from participating college and k12 schools to obtain secure Internet connectivity across campus, districts and schools when visiting other participating institutions by simply opening their computing device.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering. \n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Other", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find one of our state Eduroam purveyors and ask for one.", "rarity": "Uncommon", "timestamp": "9/26/2023 21:32:27" }, { "title": "Portable minibadge holder (pendant or earring)", "author": "RuShan", "profilePictureUrl": "", "frontImageUrl": "images/2023/portable-minibadge-holder-pendant-or-earring-front.png", "backImageUrl": "images/2023/portable-minibadge-holder-pendant-or-earring-back.png", "description": "Wanted to make a portable single minibadge holder last year which was the first version. This year I updated it with a clock circuit so all minibadges (unless they need a lot of voltage) can be used and displayed on a necklace, earrings, or almost anywhere. Option to get a special simple butterfly minibadge as well.", "specialInstructions": "", "solderingInstructions": "https://youtu.be/-dMSakdh-0s", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Badge Accessory", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Talk to me in person or DM me on discord @ahall", "rarity": "Super Rare", "timestamp": "9/27/2023 10:29:47" }, { "title": "RAY-MAN", "author": "Ray-Man", "profilePictureUrl": "", "frontImageUrl": "images/2023/ray-man-front.png", "backImageUrl": "images/2023/ray-man-back.png", "description": "Ray-Man has to have an appearance at the con. I wanted a pixel badge so I made one.", "specialInstructions": "", "solderingInstructions": "Begin on the back side first, LED Direction- Green goes in the box, Notice that both LEDs are different directions so pay attention.\n• Solder the two LEDs first, using the single-pad method for hand soldering. • Solder the two Resistors using the same single-pad method for hand soldering. • Solder the 4x 2-Position headers, with so you can read RAY-MAN without the use of a mirror.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Ask and you shall receive. Demand one and you might have to trade.", "rarity": "Rare", "timestamp": "9/27/2023 19:24:39" }, { "title": "K-9", "author": "Ray-Man", "profilePictureUrl": "", "frontImageUrl": "images/2023/k-9-front.png", "backImageUrl": "images/2023/k-9-back.png", "description": "I saw that Berly was bringing Marvin to the con. He has to have his trusty counterpart to keep him out of trouble, so I made a K-9 minibadge.", "specialInstructions": "", "solderingInstructions": "Begin on the back side first, LED Direction- Green goes in the box, So they face up if K-9 is not standing on his head.\n• Solder the two LEDs first, using the single-pad method for hand soldering. • Solder the two Resistors using the same single-pad method for hand soldering. • Solder the 4x 2-Position headers, so K-9 can stare into your eyes without looking through a muddy window.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "If you get have a Marvin the Martian from Berly come see me and ask for one and you shall get one (while supplies last). If Marvin does not accompany you then you might be forced to trade.", "rarity": "Super Rare", "timestamp": "9/27/2023 19:33:10" }, { "title": "Hello Kitty", "author": "Ray-Man", "profilePictureUrl": "", "frontImageUrl": "images/2023/hello-kitty-front.png", "backImageUrl": "images/2023/hello-kitty-back.png", "description": "I have a coworker that makes fun for us geeking out over these silly little things. She said that the only cool MiniBadge would be a Hello Kitty one. So I had to oblige and make one.", "specialInstructions": "", "solderingInstructions": "Begin on the back side first, LED Direction- Green goes in the box, Left hand side\n• Solder the LED first, using the single-pad method for hand soldering. • Solder the Resistor using the same single-pad method for hand soldering. • Solder the 4x 2-Position headers, with her looking at you so you can tell Hello Kitty how pretty while you work.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade.", "rarity": "Super Rare", "timestamp": "9/27/2023 19:38:55" }, { "title": "Squidward the Great", "author": "Ray-Man", "profilePictureUrl": "", "frontImageUrl": "images/2023/squidward-the-great-front.png", "backImageUrl": "images/2023/squidward-the-great-back.png", "description": "Come and ask me and I'll tell you.", "specialInstructions": "", "solderingInstructions": "Begin on the back side first, LED Direction- Green goes in the box, Notice that both LEDs are different directions so pay attention.\n• Solder the two LEDs first, using the single-pad method for hand soldering. • Solder the two Resistors using the same single-pad method for hand soldering. • Solder the 4x 2-Position headers, so you can see Squidward's happy face.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "If you know my first name and I know yours, then come and ask or trade.", "rarity": "Super Rare", "timestamp": "9/27/2023 19:44:27" }, { "title": "DeerJeep", "author": "KnifeMaker", "profilePictureUrl": "", "frontImageUrl": "images/2023/deerjeep-front.jpg", "backImageUrl": "images/2023/deerjeep-back.jpg", "description": "It is a Deer/Jeep thing.", "specialInstructions": "", "solderingInstructions": "Pretty easy to assembly. One LED and One Resistor.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me.", "rarity": "Super Rare", "timestamp": "9/28/2023 21:31:02" }, { "title": "WARTHOG MINIBADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/warthog-minibadge-front.png", "backImageUrl": "images/2023/warthog-minibadge-back.png", "description": "In memory of alot of peoples first crack at modding systems. This badge takes up 3 badge slots, but i think its worth it. NOTE: The Single LED goes in the location marked \"D4\" at the top of the badge.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistors using the single-pad method for hand soldering. \n• The single LED is a multicolor LED. This LED goes in the cannon slot. (D4)\n• Solder the Pin Headers to the Badge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade or barter for one of these unique badges.", "rarity": "Super Rare", "timestamp": "9/29/2023 10:17:26" }, { "title": "BADGE HOG, BADGE EXTENSION", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/badge-hog-badge-extension-front.png", "backImageUrl": "images/2023/badge-hog-badge-extension-back.png", "description": "This is an accessory designed for those oversized badges you still want to show off on your badge. There are 2 designs availble. The original Badge Hog, and the Badge Hog Submarine. The Submarine has lights that blink with the clock.", "specialInstructions": "", "solderingInstructions": "I recommend putting a badge in the supplied female connectors to get the correct spacing. Solder the female connectors first. Then flip the badge over and solder the pin headers. This can be difficult to do, so try not to bridge any connections. You can solder only 1 or both sides depending on if you want this to be a right, or left side extension.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Badge Accessory", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Look these up in the Saintcon Classifieds on the badgelife page for current cost and inventory.", "rarity": "Super Rare", "timestamp": "9/29/2023 10:28:51" }, { "title": "LVT", "author": "Parzi", "profilePictureUrl": "", "frontImageUrl": "images/2023/lvt-front.png", "backImageUrl": "images/2023/lvt-back.png", "description": "LVT is the company I have worked for, for the last 6 years, I love what they stand for and what they are doing so I decided to take their logo (with permission) for my first ever minibadge to represent.", "specialInstructions": "", "solderingInstructions": "Two LEDs and two Resistors it does not matter which color goes where as they are meant to mix \"colors\" to form a unique color. Solder each resistor to R1 and R2 and the LEDs to D1 and D2", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me", "rarity": "Super Rare", "timestamp": "9/29/2023 11:41:42" }, { "title": "I ❤\tMinibadges", "author": "Parzi", "profilePictureUrl": "", "frontImageUrl": "images/2023/i-minibadges-front.png", "backImageUrl": "images/2023/i-minibadges-back.png", "description": "This was inspired by my favorite Disney Pin and expresses my second favorite part of Saintcon so it felt only fitting to share this badge with those who also love collecting as I do.", "specialInstructions": "", "solderingInstructions": "2 Red LEDs on D1 and D2 two resistors on R1 and R2 mounted normally.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me, If you have 0 come talk to me and I might have an extra to start your collection", "rarity": "Rare", "timestamp": "9/29/2023 11:53:47" }, { "title": "WHERES PERRY?", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/wheres-perry-front.png", "backImageUrl": "images/2023/wheres-perry-back.png", "description": "Phineas and Ferb inspired badge. Doofenshmirtz Evil Incorporated, also known as Doofenshmirtz Evil Inc. or Doofenshmirtz Corporation, is a company owned by the evil scientist Dr. Heinz Doofenshmirtz. Most of the daily operations of the company are run by Doofenshmirtz himself.", "specialInstructions": "", "solderingInstructions": "This thing is tricky to build to say the least. Get the LEDS soldered according to the image below Becareful not to give them too much length as it will get in the way of the holder. Then solder the pin headers and use the addidtional pin header to put Perry on LAST. I did not include the LED or resistor for the middle of this badge. Put Perry on last. I did not include a resistor or LED for D1 or R1. This LED is tied to the CLK pin and was overkill, but can be added if one wanted to add a blinking effect to the window.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade or barter to get one of these.", "rarity": "Super Rare", "timestamp": "9/29/2023 13:39:31" }, { "title": "Support Your Local Cryptid", "author": "DistinctM1nd", "profilePictureUrl": "", "frontImageUrl": "images/2023/support-your-local-cryptid-front.png", "backImageUrl": "images/2023/support-your-local-cryptid-back.png", "description": "This badge has a hidden message that will be easier to find than the components. The components for this badge are like cryptids, impossible to see.", "specialInstructions": "", "solderingInstructions": "Install the header pins last as they make installing the components more difficult. Check to see if each LED is working as you install them. Use the top right header pins to do this, just don't solder them until the end. All of the LEDS, except D1, are green. The resistors that go with the green LEDs (R2-R5) are also marked green. D1 is yellow and its resistor (R1) is the one not colored green. Don't go by component counts to determine where they go because I included extras for all except D2. The marking for R2 is hard to see so refer to the back image here. Start with D1 and R1. These are the only components that aren't marked with green marker. After this, work through each resistor and LED verifying that each LED works as you solder them. The resistors are associated with their LED by number so R2 goes with D2 etc. D3 is hard to see the orientation. The side with a pad shaped like a T is the cathode. Optional: Cover the moon and it's LED (D1) with a spot of hot glue.", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade or barter", "rarity": "Super Rare", "timestamp": "9/29/2023 16:51:32" }, { "title": "The Haunting Specter", "author": "DistinctM1nd", "profilePictureUrl": "", "frontImageUrl": "images/2023/the-haunting-specter-front.png", "backImageUrl": "images/2023/the-haunting-specter-back.png", "description": "We needed a Halloween minibadge with Saintcon's proximity to Oct 31!", "specialInstructions": "", "solderingInstructions": "Refer to the back image to see LED orientation since it is difficult to see on the badge. R2 is below R1. D1, D2 and D3 are red LEDs which are marked with red marker. D4 is an orange LED. The resistors (left side) are all 68 ohm. \nSolder the resistors (R1 - R4). The orientation for them doesn't matter. \nSolder D4 paying attention to orientation. \nSolder D1 - D3 paying attention to orientation. D1-D3 are reverse mounted so that they shine toward the board. The orientation for polarity is still the same, just turn them over to reverse mount them. You want them to shine directly toward the board as opposed to out.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade, barter or attend my talk (can't guarantee everyone who attends my talk will get one)", "rarity": "Rare", "timestamp": "9/29/2023 17:19:02" }, { "title": "Magic Square", "author": "DistinctM1nd", "profilePictureUrl": "", "frontImageUrl": "images/2023/magic-square-front.png", "backImageUrl": "images/2023/magic-square-back.png", "description": "A magic square is a square grid of numbers where the sum of each row, column, and diagonal is constant. Its origin dates back centuries, with roots in ancient Eastern and Western cultures. It is common to see magic squares with Hebrew characters because each character also represents a number.", "specialInstructions": "", "solderingInstructions": "Solder the LEDs (D1 - D4) paying attention to orientation. The LEDs are all the same color (blue). Solder the resistors (R1-R4). The resistors are all 5 ohm. Solder the 4 header pins.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade or barter", "rarity": "Super Rare", "timestamp": "9/29/2023 17:50:43" }, { "title": "Smaug the Terrible", "author": "Light", "profilePictureUrl": "", "frontImageUrl": "images/2023/smaug-the-terrible-front.png", "backImageUrl": "images/2023/smaug-the-terrible-back.png", "description": "Smaug was considered to be the last \"great\" dragon of Middle-earth during the Third Age. He captured the Lonely Mountain, forced the dwarves into exile, and claimed their treasure for himself. This minibadge features animated/flickering LEDs to help portray this infamous, fire-breathing dragon.", "specialInstructions": "", "solderingInstructions": "1. Solder the ATTiny85 using the single-pad soldering method.\n2. Solder the resistors and LEDs using the single-pad soldering method.\n- 10K ohm resistor (green circle): R4\n- 62 ohm resistors (blue circles): R1, R2, and R3\n- Orange LED: D2\n- Yellow LEDs: D1 and D3\n3. Solder the 3x 2-position headers.\n4. Cover the LEDs and unmasked area on the back with hot glue (provided at the Hardware Hacking Community).", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Light at the Hardware Hacking Community (soldering area) and ask for one.", "rarity": "Super Rare", "timestamp": "9/29/2023 18:32:50" }, { "title": "Avatar Airbending Badge", "author": "goodn3rd", "profilePictureUrl": "", "frontImageUrl": "images/2023/avatar-airbending-badge-front.png", "backImageUrl": "images/2023/avatar-airbending-badge-back.png", "description": "Taking inspiration from creators before us, we wanted to make a themed set from the Avatar: The Last Airbender world for each of our party to trade and distribute.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED Direction indicators are on the image above. (Green goes into the garage)\n• Solder the two LEDs first, using the single-pad method for hand soldering.\n• Solder the two resistors using the same single-pad method for hand soldering.\n• Solder the 4x 2-Position headers, with the artwork facing out.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find H4mmer around the community area and trade (or teach them something interesting).", "rarity": "Super Rare", "timestamp": "9/29/2023 18:42:33" }, { "title": "Avatar Earthbending Badge", "author": "goodn3rd", "profilePictureUrl": "", "frontImageUrl": "images/2023/avatar-earthbending-badge-front.png", "backImageUrl": "images/2023/avatar-earthbending-badge-back.png", "description": "Taking inspiration from creators before us, we wanted to make a themed set from the Avatar: The Last Airbender world for each of our party to trade and distribute.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED Direction indicators are on the image above. (Green goes into the garage)\n• Solder the two LEDs first, using the single-pad method for hand soldering.\n• Solder the two resistors using the same single-pad method for hand soldering.\n• Solder the 4x 2-Position headers, with the artwork facing out.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Steelhead345 around the community area and trade (or teach them something interesting).", "rarity": "Super Rare", "timestamp": "9/29/2023 18:47:19" }, { "title": "Avatar Firebending Badge", "author": "goodn3rd", "profilePictureUrl": "", "frontImageUrl": "images/2023/avatar-firebending-badge-front.png", "backImageUrl": "images/2023/avatar-firebending-badge-back.png", "description": "Taking inspiration from creators before us, we wanted to make a themed set from the Avatar: The Last Airbender world for each of our party to trade and distribute.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED Direction indicators are on the image above. (Green goes into the garage)\n• Solder the two LEDs first, using the single-pad method for hand soldering.\n• Solder the two resistors using the same single-pad method for hand soldering.\n• Solder the 4x 2-Position headers, with the artwork facing out.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Cyb3rKnight around the community area and trade (or teach them something interesting).", "rarity": "Super Rare", "timestamp": "9/29/2023 18:52:19" }, { "title": "Avatar Metalbending Badge", "author": "goodn3rd", "profilePictureUrl": "", "frontImageUrl": "images/2023/avatar-metalbending-badge-front.png", "backImageUrl": "images/2023/avatar-metalbending-badge-back.png", "description": "Taking inspiration from creators before us, we wanted to make a themed set from the Avatar: The Last Airbender world for each of our party to trade and distribute.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED Direction indicators are on the image above. (Green goes into the garage)\n• Solder the two LEDs first, using the single-pad method for hand soldering.\n• Solder the two resistors using the same single-pad method for hand soldering.\n• Solder the 4x 2-Position headers, with the artwork facing out.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Curosive around the community area and trade (or teach them something interesting).", "rarity": "Super Rare", "timestamp": "9/29/2023 18:56:12" }, { "title": "Avatar Tech Badge", "author": "goodn3rd", "profilePictureUrl": "", "frontImageUrl": "images/2023/avatar-tech-badge-front.png", "backImageUrl": "images/2023/avatar-tech-badge-back.png", "description": "Taking inspiration from creators before us, we wanted to make a themed set from the Avatar: The Last Airbender world for each of our party to trade and distribute.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED Direction indicators are on the image above. (Green goes into the garage)\n• Solder the two LEDs first, using the single-pad method for hand soldering.\n• Solder the two resistors using the same single-pad method for hand soldering.\n• Solder the 4x 2-Position headers, with the artwork facing out.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find goodn3rd around the community area and trade (or teach them something interesting).", "rarity": "Super Rare", "timestamp": "9/29/2023 19:02:11" }, { "title": "Avatar Waterbending Badge", "author": "goodn3rd", "profilePictureUrl": "", "frontImageUrl": "images/2023/avatar-waterbending-badge-front.png", "backImageUrl": "images/2023/avatar-waterbending-badge-back.png", "description": "Taking inspiration from creators before us, we wanted to make a themed set from the Avatar: The Last Airbender world for each of our party to trade and distribute.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED Direction indicators are on the image above. (Green goes into the garage)\n• Solder the two LEDs first, using the single-pad method for hand soldering.\n• Solder the two resistors using the same single-pad method for hand soldering.\n• Solder the 4x 2-Position headers, with the artwork facing out.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Mister X around the community area and trade (or teach them something interesting).", "rarity": "Super Rare", "timestamp": "9/29/2023 19:07:26" }, { "title": "Avatar Weapons Badge", "author": "goodn3rd", "profilePictureUrl": "", "frontImageUrl": "images/2023/avatar-weapons-badge-front.png", "backImageUrl": "images/2023/avatar-weapons-badge-back.png", "description": "Taking inspiration from creators before us, we wanted to make a themed set from the Avatar: The Last Airbender world for each of our party to trade and distribute.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED Direction indicators are on the image above. (Green goes into the garage)\n• Solder the two LEDs first, using the single-pad method for hand soldering.\n• Solder the two resistors using the same single-pad method for hand soldering.\n• Solder the 4x 2-Position headers, with the artwork facing out.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Baxter24 around the community area and trade (or teach them something interesting).", "rarity": "Super Rare", "timestamp": "9/29/2023 19:10:49" }, { "title": "Doors of Durin", "author": "Light", "profilePictureUrl": "", "frontImageUrl": "images/2023/doors-of-durin-front.png", "backImageUrl": "images/2023/doors-of-durin-back.png", "description": "The designs on the Doors of Durin were made from ithildin which could only be seen by the reflected light of the moon and stars. The inscription, \"Pedo Mellon a Minno\" (Speak Friend and Enter), was a riddle. The answer was the Elvish word for friend, mellon.", "specialInstructions": "", "solderingInstructions": "1. Solder both resistors using the single-pad method for hand soldering.\n2. Solder both LEDs using the single-pad method for hand soldering.\n3. Solder the 4x 2-Position headers.\n4. To distribute the light evenly, cover the entire back of the minibadge (including the LEDs) with hot glue (provided at the Hardware Hacking Community).", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Light at the Hardware Hacking Community (soldering area) and ask for one.", "rarity": "Super Rare", "timestamp": "9/29/2023 19:27:28" }, { "title": "The Spider's Bane", "author": "Light", "profilePictureUrl": "", "frontImageUrl": "images/2023/the-spiders-bane-front.png", "backImageUrl": "images/2023/the-spiders-bane-back.png", "description": "In \"The Lord of the Rings\" film series, this Elven dagger is engraved with the words: “Maegnas aen estar nin dagnir in yngyl im.\" (Sting is my name. I am the spider’s bane.) The blade glows blue when Orcs are near.", "specialInstructions": "", "solderingInstructions": "1. Solder the resistor using the single-pad method for hand soldering.\n\n2. Solder the LED using the single-pad method for hand soldering.\n\n3. Solder the 4x 2-Position headers.\n\n4. Cover the LEDs and unmasked area on the back with hot glue (provided at the Hardware Hacking Community).", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Light at the Hardware Hacking Community (soldering area) and ask for one.", "rarity": "Super Rare", "timestamp": "9/29/2023 19:36:15" }, { "title": "Wizzards", "author": "Light", "profilePictureUrl": "", "frontImageUrl": "images/2023/wizzards-front.png", "backImageUrl": "images/2023/wizzards-back.png", "description": "“A wizard is never late, Frodo Baggins. Nor is he early. He arrives precisely when he means to.” - Gandalf the Gray", "specialInstructions": "", "solderingInstructions": "1. Solder the resistors using the single-pad method for hand soldering.\n\n2. Solder the LEDs using the single-pad method for hand soldering.\n\n3. Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Light at the Hardware Hacking Community (soldering area) and ask for one.", "rarity": "Super Rare", "timestamp": "9/29/2023 19:38:09" }, { "title": "Electirrpicttomiomer", "author": "DistinctM1nd", "profilePictureUrl": "", "frontImageUrl": "images/2023/electirrpicttomiomer-front.png", "backImageUrl": "images/2023/electirrpicttomiomer-back.png", "description": "The Electirrpicttomiomer uses a tiny flow of electrons to measure the physical energy of the mind.", "specialInstructions": "", "solderingInstructions": "Solder the opamp to the back. Solder R1 and R3 (they are 10k ohm resistors and are marked 1002). Bridge the pads on R4 with solder. R4 is in series with the potentiometer and is not needed because the potentiometer covers the range of resistance required. Solder the 3.3k ohm resistor (marked 3301) to R6. Solder the 12k ohm resistor (marked 123) to R7. Note that R6 is in series with D1 (orange) and R7 is in series with D2 (green). These are much higher resistances than you'd typically use with these LEDs. I chose these resistors because I wanted the LEDs to be easy to view while using the badge and to also appear \"vintage.\" Solder D1 (orange) to the front. Solder D2 (green) to the front. Solder the potentiometer to the front. Solder the 2 pin female header to the front (bottom). This is what you'll connect the two cans. Solder the 4 header pins. Break the remaining 2 pin male header into two pieces so that each has one pin. Solder a male header pin to each of the cans. \n\nThis badge will come with an operating manual.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "I'll only have a small number of these so you'll have to convince me to trade one.", "rarity": "Super Rare", "timestamp": "9/29/2023 19:45:29" }, { "title": "Haunting Specter Minibadge Holder", "author": "DistinctM1nd", "profilePictureUrl": "", "frontImageUrl": "images/2023/haunting-specter-minibadge-holder-front.png", "backImageUrl": "images/2023/haunting-specter-minibadge-holder-back.png", "description": "This will hold 8 minibadges and can either be powered with the Saintcon main badge or with two AA batteries. Note: Minibadges that require the clock pin will not work with the battery option.", "specialInstructions": "", "solderingInstructions": "Assembly instructions will be provided with the badge.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Badge Accessory", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "These are $15", "rarity": "Super Rare", "timestamp": "9/29/2023 22:50:08" }, { "title": "Cryptid Minibadge Expansion Board", "author": "DistinctM1nd", "profilePictureUrl": "", "frontImageUrl": "images/2023/cryptid-minibadge-expansion-board-front.png", "backImageUrl": "images/2023/cryptid-minibadge-expansion-board-back.png", "description": "This expansion board will hold 8 minibadges. It can be powered either from your main Saintcon badge (as an extension to the badge) or with 2 AA batteries. Note: Minibadges that rely on the clock pin will not work with the battery option but will work if powered from the main Saintcon badge.", "specialInstructions": "", "solderingInstructions": "Assembly instructions will be provided with the badge.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Badge Accessory", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "You'll have to find me. They are $15", "rarity": "Super Rare", "timestamp": "9/30/2023 8:57:51" }, { "title": "CRASH MINIBADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/crash-minibadge-front.png", "backImageUrl": "images/2023/crash-minibadge-back.png", "description": "This is a Throwback to one of the first PS1 Games I played Growing up. Crash Team Racing was a favorite as well.", "specialInstructions": "", "solderingInstructions": "Solder the LEDs leaving enough room to bend the LEDs. Bend one LED toward the Tiki and another toward the CRASH title. (As shown in the badge image.) Solder the resistors and pin headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade or Barter to get one of these.", "rarity": "Super Rare", "timestamp": "9/30/2023 13:58:32" }, { "title": "TRON LIGHTCYCLE MINIBADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/tron-lightcycle-minibadge-front.png", "backImageUrl": "images/2023/tron-lightcycle-minibadge-back.png", "description": "Light cycles were ridden in both the original Tron movie in 1982 and the new Tron Legacy film as part of a deadly sport where riders belted around a digital grid turning corners at breakneck speeds with the aim of cutting off their opponent causing them to crash and explode into millions of tiny glowing pixels.\n\nThis has a defect on one side of the badge, and 2 of the leds on the back wheel will not light up.", "specialInstructions": "", "solderingInstructions": "This thing is tricky to build. Due to the sheer amount of LED's and resistors in such a small form factor, many of the traces and vias cross under or between the leds. They are not masked making it extremely likely to create a short if you dont have a steady hand when soldering. Use a fine tip and the thinest solder you can find. \n\nThe design makes the silk hard to see for LED direction. There is a slik screen small white dot indicating the Cathode (-) side of the LED.", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade or barter for one of these if you dare try and assemble one!", "rarity": "Super Rare", "timestamp": "9/30/2023 14:17:07" }, { "title": "Robot badge", "author": "Kingbob", "profilePictureUrl": "", "frontImageUrl": "images/2023/robot-badge-front.png", "backImageUrl": "images/2023/robot-badge-back.png", "description": "Designed by my 6 year old, Emily. When I asked her what she wanted on a badge she immediately said \"ROBOT!\" This is what her creative mind came up with. I just converted her idea to KiCAD.", "specialInstructions": "", "solderingInstructions": "There are 2 LEDs and 2 resistors. D1 and R1 have a *RED* mark on their packaging. D2 and R2 have a *BLUE* mark.\nStart on back. Solder the blue LED to D2, the blue resistor labelled \"1000\" to R2 and the red resistor labelled \"2R20\" to R1.\nSolder the headers and then the red LED to D1 on the front with the cathode (green) end on the left.\nAdd a glob of hot glue over the blue LED and the eyes on the back of the badge to make the eyes show the color better.\n\nhttps://github.com/JonDegn/Saintcon2023-minibages/blob/main/emily-robot/readme.md", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "My daughter will be handing them out randomly at family night to other kids. I might have a few on me during the con that you could trade for.", "rarity": "Super Rare", "timestamp": "9/30/2023 21:27:57" }, { "title": "Pink Butterfly Badge", "author": "Kingbob", "profilePictureUrl": "", "frontImageUrl": "images/2023/pink-butterfly-badge-front.png", "backImageUrl": "images/2023/pink-butterfly-badge-back.png", "description": "This was designed by my 8 year old daughter. She wanted something pretty with a pink LED.", "specialInstructions": "", "solderingInstructions": "Solder the led and resistor on the back and then solder the headers.\nAdd some hot glue to the back of the board to help the LED evenly light up the butterfly wings.\n\n https://github.com/JonDegn/Saintcon2023-minibages/blob/main/elizabeth-butterfly/readme.md", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "My daughter will be handing it out to other kids at family night. I will probably have a few on me that you can trade for during the con.", "rarity": "Super Rare", "timestamp": "9/30/2023 21:40:47" }, { "title": "Word Puzzle", "author": "PB&J", "profilePictureUrl": "", "frontImageUrl": "images/2023/word-puzzle-front.jpg", "backImageUrl": "images/2023/word-puzzle-back.jpg", "description": "Three stacked, acrylic squares with icons that light up.", "specialInstructions": "", "solderingInstructions": "Watch the video, if I can't get the 3rd acrylic square's steps included, just repeat steps from the 2nd square. https://youtu.be/YMicmrvMjMY", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Figure out what the puzzle says/means, trade, tell me if there is anything significant that is hidden in any/all of the parts and what that is.", "rarity": "Rare", "timestamp": "9/30/2023 22:39:29" }, { "title": "Sailin' the Digital Seas!", "author": "Jibberjaw", "profilePictureUrl": "", "frontImageUrl": "images/2023/sailin-the-digital-seas-front.png", "backImageUrl": "images/2023/sailin-the-digital-seas-back.png", "description": "Remember when radio was going to destroy the record industry? Television was going to be the end of cinema? Home taping was killing music? Video would be the death of Hollywood? Sailing through digital waves, Pirate Bay, where freedom paves, Torrents swirling, tales unfold, In a world where bytes are gold. Yo-ho-ho, Pirate Bay's our tale, Downloading dreams, setting sail, Cyber pirates roam the tide, Bits and bytes, where we abide. Raise the flag, let freedom ring, In this virtual sea, we sing, In cyberspace, our story's told.", "specialInstructions": "", "solderingInstructions": "Two LEDs stand, a pirate's pair.\nTwo resistors guard with flair.\nIron hot, steady and true.\nSolder 'em tight, like ocean's dew.\nBridge for 'Pirate's Search', chart the sea.\nOr 'I'm Feeling Lucky', with glee.\nJoints secure, ready to throw.\nPirate's luck in soldered glow.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Arrr, these here shall be sailin' through the con!", "rarity": "Super Rare", "timestamp": "9/30/2023 23:19:44" }, { "title": "Zodiak", "author": "Zodiak", "profilePictureUrl": "", "frontImageUrl": "images/2023/zodiak-front.png", "backImageUrl": "images/2023/zodiak-back.png", "description": "It's a minibage. And it looks like a foot. Hopefully it doesn't smell like one.", "specialInstructions": "", "solderingInstructions": "Same as the rest. Pins go through the holes. LED goes in the LED slot (see guide for orientation), resistor goes in the resistor spot.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find zodiak. No closed toed shoes allowed.", "rarity": "Uncommon", "timestamp": "10/1/2023 20:57:54" }, { "title": "Chomper", "author": "SpamWizard", "profilePictureUrl": "", "frontImageUrl": "images/2023/chomper-front.png", "backImageUrl": "images/2023/chomper-back.png", "description": "This MiniBadge is a Zodiak sponsored mini Zodiak design it is mostly so I can trade for other MiniBadges.", "specialInstructions": "", "solderingInstructions": "Install the Led on the back, make sure the orientation is correct. Install the 1206 resistor and the pins.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "This minibadge will be very eaisily attainiable mostly just come say hi to me or Zodiak and we'll hook you up. Nothing that crazy about this badge.", "rarity": "Rare", "timestamp": "10/1/2023 21:28:48" }, { "title": "Family Night - Lock Pick", "author": "TGalvez", "profilePictureUrl": "", "frontImageUrl": "images/2023/family-night-lock-pick-front.png", "backImageUrl": "images/2023/family-night-lock-pick-back.png", "description": "SAINTCON Family Night, where SAINTCON can be enjoyed by the whole family! This badge represents the efforts of those that participate in the Lock Pick Community at the SAINTCON Family Night event.", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/FamilyNight-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- Solder the single resistor first.\n- Solder the LED so that it is connected on the back-side of the board, with a minimum of 1/2” standoff so the LED can be bent slightly inward.\n- After soldering, carefully bend the LED around until it is resting on the back of the board as shown above.\n- Solder the 4x 2-Position headers at the bottom of the Front side.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Event", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Available only to Family Night Attendees. Come attempt to pick a lock to collect a badge.\n\n**For those not attending family night, See TGalvez after the event for a collection of Family Night Badges.**", "rarity": "Uncommon", "timestamp": "10/2/2023 6:53:11" }, { "title": "Family Night - Nerf Blaster", "author": "TGalvez", "profilePictureUrl": "", "frontImageUrl": "images/2023/family-night-nerf-blaster-front.png", "backImageUrl": "images/2023/family-night-nerf-blaster-back.png", "description": "SAINTCON Family Night, where SAINTCON can be enjoyed by the whole family! This badge represents the efforts of those that participate in the Nerf Blasters Community at the SAINTCON Family Night event.", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/FamilyNight-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- Solder the single resistor first.\n- Solder the LED so that it is connected on the back-side of the board, with a minimum of 1/2” standoff so the LED can be bent slightly inward.\n- After soldering, carefully bend the LED around until it is resting on the back of the board as shown above.\n- Solder the 4x 2-Position headers at the bottom of the Front side.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Event", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Available only to Family Night Attendees. Come Shoot a Nerf Blaster with us at Family Night to collect. \n\n**For those not attending family night, See TGalvez after the event for a collection of Family Night Badges.**\"", "rarity": "Uncommon", "timestamp": "10/2/2023 6:58:25" }, { "title": "Family Night - Rocket Building", "author": "TGalvez", "profilePictureUrl": "", "frontImageUrl": "images/2023/family-night-rocket-building-front.png", "backImageUrl": "images/2023/family-night-rocket-building-back.png", "description": "SAINTCON Family Night, where SAINTCON can be enjoyed by the whole family! This badge represents the efforts of those that participate in the Rocket Building Community at the SAINTCON Family Night event.", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/FamilyNight-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- Solder the single resistor first.\n- Solder the LED so that it is connected on the back-side of the board, with a minimum of 1/2” standoff so the LED can be bent slightly inward.\n- After soldering, carefully bend the LED around until it is resting on the back of the board as shown above.\n- Solder the 4x 2-Position headers at the bottom of the Front side.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Event", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Available only to Family Night Attendees. Come build and launch a rocket at Family Night to Collect.\n\n**For those not attending family night, See TGalvez after the event for a collection of Family Night Badges.**", "rarity": "Uncommon", "timestamp": "10/2/2023 7:01:33" }, { "title": "Family Night - Badge Soldering", "author": "TGalvez", "profilePictureUrl": "", "frontImageUrl": "images/2023/family-night-badge-soldering-front.png", "backImageUrl": "images/2023/family-night-badge-soldering-back.png", "description": "SAINTCON Family Night, where SAINTCON can be enjoyed by the whole family! This badge represents the efforts of those that participate in the Hardware Hacking Community at the SAINTCON Family Night event.", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/FamilyNight-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- Solder the single resistor first.\n- Solder the LED so that it is connected on the back-side of the board, with a minimum of 1/2” standoff so the LED can be bent slightly inward.\n- After soldering, carefully bend the LED around until it is resting on the back of the board as shown above.\n- Solder the 4x 2-Position headers at the bottom of the Front side.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Event", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Available only to Family Night Attendees. Come assemble your Family Night badge with us at Family Night to collect. \n\n**For those not attending family night, See TGalvez after the event for a collection of Family Night Badges.**", "rarity": "Uncommon", "timestamp": "10/2/2023 7:07:47" }, { "title": "Family Night - Code Breakers", "author": "Professor Plum", "profilePictureUrl": "", "frontImageUrl": "images/2023/family-night-code-breakers-front.jpg", "backImageUrl": "images/2023/family-night-code-breakers-back.png", "description": "SAINTCON Family Night, where SAINTCON can be enjoyed by the whole family! This badge represents the efforts of those that participate in the Cryptography Community at the SAINTCON Family Night event.", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/FamilyNight-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- Solder the single resistor first.\n- Solder the LED so that it is connected on the back-side of the board, with a minimum of 1/2” standoff so the LED can be bent slightly inward.\n- After soldering, carefully bend the LED around until it is resting on the back of the board as shown above.\n- Solder the 4x 2-Position headers at the bottom of the Front side.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Event", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Available only to Family Night Attendees. Anyone who completes a puzzle can get a minibadge. If you complete the substitution cipher you can collect a key!\n\n**For those not attending family night, See TGalvez after the event for a collection of Family Night Badges.**", "rarity": "Uncommon", "timestamp": "10/2/2023 7:11:43" }, { "title": "Hackers Challenge", "author": "Santiago", "profilePictureUrl": "", "frontImageUrl": "images/2023/hackers-challenge-front.png", "backImageUrl": "images/2023/hackers-challenge-back.png", "description": "Designed by Santiago, with inspiration from Rigel and Zevlag, the Hackers Challenge Minibadge is common badge to find at SAINTCON.", "specialInstructions": "", "solderingInstructions": "ASSEMBLY INSTRUCTIONS:\n- This badges comes mostly assembled.\n- Begin on the Back side.\n- Solder the Jumper at the bottom of the board, bridging EITHER the SOLID or BLINK (clock) side, Never Solder across all three.\n- Solder the 3x 2-Position headers in each of the 3 corners on the Front side.\n- (There should be 4 holes without pins. I wonder why they’d do that…)", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Contest", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "You can obtain one by interacting with one of the Game Masters for the Hackers Challenge game. They MAY make you solve at least one puzzle to earn one, but then again, maybe not.\n\nGet started at https://www.HackersChallenge.org/", "rarity": "Common", "timestamp": "10/2/2023 7:19:31" }, { "title": "Here Come The Grannies", "author": "TGalvez", "profilePictureUrl": "", "frontImageUrl": "images/2023/here-come-the-grannies-front.png", "backImageUrl": "images/2023/here-come-the-grannies-back.png", "description": "In true Bluey form, “Here Come the Grannies!” “Oh!, I dropped my coins!”", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/Zevlag-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- LED Direction indicators are on the image above, and on the board with icons.\n- Solder the 4 LEDs first.\n D1, D2 = 1206 Green LEDs\n D3, D4 = 0603 Purple LEDs\n- Solder the 2 resistors next.\n R1 = 10 Ω (1206) for Green LEDs\n R2 = 75 Ω (1206) for Purple LEDs\n- Solder the 3x 2-Position headers on the Front side.\n- Solder the 1x 1-Position headers on the Front side.\n- For the best illumination effect cover the back, including LEDs, with 2 separate globs of hot glue.", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Figure out who Z5Zebra is and ask Him what his favorite Bluey episode is.", "rarity": "Rare", "timestamp": "10/2/2023 7:23:54" }, { "title": "Bodge Badge", "author": "Zevlag", "profilePictureUrl": "", "frontImageUrl": "images/2023/bodge-badge-front.png", "backImageUrl": "images/2023/bodge-badge-back.png", "description": "Sometimes we all make mistakes, so here I am, looking like my favorite emoji.", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/Zevlag-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- LED Direction indicators are on the image above, and on the PCB with box icon.\n- Solder the 2 LEDs first.\n D1, D2 = 1206 White LEDs\n- Solder the 2 resistors next.\n R1 = 10 Ω (1206) for White LEDs\n- Solder the Jumper at the bottom of the board, bridging EITHER the SOLID or BLINK (clock) side, Never Solder across all three.\n- Solder the 4x 2-Position headers on the Front side.\n- Use your Bodge wire to make it work.\n- Attach googly eyes to front.\n- For the best illumination effect cover the openings on the back, including LEDs, with globs of hot glue.", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Zevlag and tell him one of your favorite bodge/hacking story.", "rarity": "Rare", "timestamp": "10/2/2023 7:30:09" }, { "title": "Bones - Dr. Temperance", "author": "TGalvez", "profilePictureUrl": "", "frontImageUrl": "images/2023/bones-dr-temperance-front.png", "backImageUrl": "images/2023/bones-dr-temperance-back.png", "description": "Part of the “Bones” Collection. This collection came about as a way for a band loving kid to have minibadges to trade and still be able to offer his inspiration badge—the Trombone Badge, as an ultra rare badge. Collect all 5 “Bones” badges to qualify to to collect a Trombone.\n\nThis “Bones” badge is inspired by the TV Show, “Bones”.", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/Zevlag-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- LED Direction indicators are on the image above, and on the PCB with box icon.\n- Solder the 2 LEDs first.\n D1, D2 = 1206 Blue LEDs\n- Solder the 2 resistors next.\n R1 = 10 Ω (1206) for Blue LEDs\n- Solder the 4x 2-Position headers on the Front side.\n- For the best illumination effect cover the back, including LEDs, with globs of hot glue.-", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Z2Orca and bring something to trade.", "rarity": "Rare", "timestamp": "10/2/2023 7:33:33" }, { "title": "Bones - Knuckles", "author": "TGalvez", "profilePictureUrl": "", "frontImageUrl": "images/2023/bones-knuckles-front.jpg", "backImageUrl": "images/2023/bones-knuckles-back.jpg", "description": "Part of the “Bones” Collection. This collection came about as a way for a band loving kid to have minibadges to trade and still be able to offer his inspiration badge—the Trombone Badge, as an ultra rare badge. Collect all 5 “Bones” badges to qualify to to collect a Trombone.\n\nForget Hi-5, give me Bones!", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/Zevlag-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- LED Direction indicators are on the image above, and on the PCB with box icon.\n- Solder the 2 LEDs first.\n D1, D2 = 0603 Purple LEDs\n- Solder the 2 resistors next.\n R1 = 10 Ω (1206) for Purple LEDs\n- Solder the 4x 2-Position headers on the Front side.\n- For the best illumination effect cover the back, including LEDs, with globs of hot glue.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Z2Orca and bring something to trade…and don’t forget to give him bones!", "rarity": "Rare", "timestamp": "10/2/2023 7:36:18" }, { "title": "Bones - McCoy", "author": "TGalvez", "profilePictureUrl": "", "frontImageUrl": "images/2023/bones-mccoy-front.png", "backImageUrl": "images/2023/bones-mccoy-back.png", "description": "Part of the “Bones” Collection. This collection came about as a way for a band loving kid to have minibadges to trade and still be able to offer his inspiration badge—the Trombone Badge, as an ultra rare badge. Collect all 5 “Bones” badges to qualify to to collect a Trombone.\n\nThe real McCoy!", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/Zevlag-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- LED Direction indicators are on the image above, and on the PCB with box icon.\n- Solder the 2 LEDs first.\n D1, D2 = 0805 Yellow LEDs\n- Solder the single resistor next.\n R1 = 100 Ω (1206) for Yellow LEDs\n- Solder the 4x 2-Position headers on the Front side.\n- For the best illumination effect cover opening on the back, including LEDs, with a glob of hot glue.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Z2Orca and bring something to trade.", "rarity": "Rare", "timestamp": "10/2/2023 7:38:45" }, { "title": "Bones - Them Dry Bones", "author": "TGalvez", "profilePictureUrl": "", "frontImageUrl": "images/2023/bones-them-dry-bones-front.png", "backImageUrl": "images/2023/bones-them-dry-bones-back.png", "description": "Part of the “Bones” Collection. This collection came about as a way for a band loving kid to have minibadges to trade and still be able to offer his inspiration badge—the Trombone Badge, as an ultra rare badge. Collect all 5 “Bones” badges to qualify to to collect a Trombone.\n\n“Them Bones, Them Bones Gonna, Walk Around!”", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/Zevlag-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- LED Direction indicators are on the image above, and on the PCB with box icon.\n- Solder the 3 LEDs first.\n D1, D2, D3 = 0805 White LEDs\n- Solder the single resistor next.\n R1 = 22 Ω (1206) for White LEDs\n- Solder the 4x 2-Position headers on the Front side.\n- For the best illumination effect cover opening on the back, including LEDs, with a glob of hot glue", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Z2Orca and bring something to trade.", "rarity": "Rare", "timestamp": "10/2/2023 7:41:24" }, { "title": "Bones - T-Bone Steak", "author": "TGalvez", "profilePictureUrl": "", "frontImageUrl": "images/2023/bones-t-bone-steak-front.png", "backImageUrl": "images/2023/bones-t-bone-steak-back.png", "description": "Part of the “Bones” Collection. This collection came about as a way for a band loving kid to have minibadges to trade and still be able to offer his inspiration badge—the Trombone Badge, as an ultra rare badge. Collect all 5 “Bones” badges to qualify to to collect a Trombone.\n\nDon’t forget the Sauce! (Carolina Barbecue that is!)", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/Zevlag-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- LED Direction indicators are on the image above, and on the board with icons.\n- Solder the 2 LEDs first.\n D1, D2, D3 = 1206 Red LEDs\n- Solder the single resistor next.\n R1 = 30 Ω (1206) for Red LEDs\n- Solder the 4x 2-Position headers on the Front side.\n- For the best illumination effect cover opening on the back, including LEDs, with a glob of hot glue.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Z2Orca and bring something to trade.", "rarity": "Rare", "timestamp": "10/2/2023 7:43:21" }, { "title": "Climb On", "author": "Zevlag", "profilePictureUrl": "", "frontImageUrl": "images/2023/climb-on-front.png", "backImageUrl": "images/2023/climb-on-back.png", "description": "Inspired by a love of climbing—both in the mountains and on the wall in the gym.", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/Zevlag-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- LED Direction indicators are on the image above, and on the board with icons.\n- Solder the 2 LEDs first.\n D1 = 1206 Green LED\n D2 = 1206 Blue LED\n- Solder the 2 resistors next.\n R1 = 10 Ω (1206) for Green LED\n R2 = 10 Ω (1206) for Blue LED\n- Solder the 4x 2-Position headers on the Front side.\n- For the best illumination effect cover the openings on the back, including LEDs, with 2 separate globs of hot glue.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Zevlag and share a favorite hobby!", "rarity": "Rare", "timestamp": "10/2/2023 7:45:39" }, { "title": "Daisy Duck", "author": "TGalvez", "profilePictureUrl": "", "frontImageUrl": "images/2023/daisy-duck-front.png", "backImageUrl": "images/2023/daisy-duck-back.png", "description": "Who’s Minnie without her best friend, Daisy! Badge fits perfectly next to her sister badge of last year, the Minnie Badge.\n\n“I just know we’ll have oodles of fun together! I’m Daisy Duck, but you can call me Daisy. We’ve all just been dying to meet you!”", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/Zevlag-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nBodge wire required! NOTE: The indicated bodge wire is required for all LEDs to illuminate.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- LED Direction indicators are on the image above, and on the board with icons.\n- Solder the 4 LEDs first.\n D1, D2 = 1206 Pink LEDs\n D3, D4 = 0603 Purple LEDs\n D5 = 1206 Red LED\n- Solder the 3 resistors next.\n R1 = 22 Ω (1206) for Green LEDs (please check the updated build link above)\n R2 = 22 Ω (1206) for Purple LEDs\t (please check the updated build link above)\n R3 = 130 Ω (1206) for Red LED\t\t (please check the updated build link above)\n- Solder a bodge wire from the bottom of R2 to the top of R3\n- Solder the 4x 2-Position headers on the Front side.\n- For the best illumination effect cover openings on the back, including LEDs, with 3 separate globs of hot glue.-", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find TGalvez and toss in your vote for which of the crew should make a debut next year!", "rarity": "Rare", "timestamp": "10/2/2023 7:51:57" }, { "title": "JoyCon", "author": "TGalvez", "profilePictureUrl": "", "frontImageUrl": "images/2023/joycon-front.png", "backImageUrl": "images/2023/joycon-back.png", "description": "1, 2, Switch!", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/Zevlag-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- Check the year at the top to orient top and bottom.\n- LED Direction indicators are on the image above, and on the board with icons.\n- Solder the 8 LEDs first.\n D1, D2, D7, D8 = 1206 Blue LEDs\n D3, D4, D5, D6 = 1206 Red LEDs\n- Solder the 4 resistors next.\n R1, R4 = 10 Ω (1206) for Blue LEDs\n R2, R3 = 30 Ω (1206) for Red LEDs\n- Solder the 4x 2-Position headers on the Front side.\n- For the best illumination effect cover the back, including LEDs, with 2 separate globs of hot glue.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Z4Dolphin and tell him your favorite game!", "rarity": "Rare", "timestamp": "10/2/2023 7:55:43" }, { "title": "MiniGolf", "author": "TGalvez & Zevlag", "profilePictureUrl": "", "frontImageUrl": "images/2023/minigolf-front.png", "backImageUrl": "images/2023/minigolf-back.png", "description": "Toss on your VR headset of choice and download Walkabout Mini golf to enjoy the multiplayer game that has brought conference committee members stress relief over the months as they’ve planned this year’s con.", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/Zevlag-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- LED Direction indicators are on the image above, and on the board with icons.\n- Solder the 3 LEDs first.\n D1, D3 = 1206 Green LEDs\n D2 = 1206 Red LED\n- Solder the 2 resistors next.\n R1 = 10 Ω (1206) for Green LEDs\n R2 = 75 Ω (1206) for Red LED\n- Solder the 4x 2-Position headers on the Front side.\n- For the best illumination effect cover the opening on the back, including LEDs, with 2 separate globs of hot glue.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Zevlag and chat VR experiences to collect!", "rarity": "Rare", "timestamp": "10/2/2023 7:57:49" }, { "title": "More than a Bug", "author": "Z1Dragonfly", "profilePictureUrl": "", "frontImageUrl": "images/2023/more-than-a-bug-front.png", "backImageUrl": "images/2023/more-than-a-bug-back.png", "description": "This badge is a play on words. My Namesake, The dragonfly is a “bug” and my Pun-loving mind found a joke. To most people if I’m “bugging you” I am being pretty annoying, but in the cybersecurity community I could be a bug in your code, or a bug to spy on you. This Minibadge is my first step into PCB design, as I learned to use KiCad. I hope you enjoy!", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/Zevlag-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- Solder the single resistor first.\n R1 = 75 Ω (1206) for Red LED\n- Solder the LED so that it is connected on the back-side of the board, with a minimum of 1/2” standoff so the LED can be bent slightly - inward.\n D1 = 3mm Red LED\n- After soldering, carefully bend the LED around until it is resting on the back of the board as shown above.\n- Cut one of 2-Position headers and place a single pin in each hole at the top.\n- Solder the 2x 2-Position headers at the bottom of the Front side.-", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "In order to obtain this Minibadge, find me and bring something in exchange.", "rarity": "Rare", "timestamp": "10/2/2023 8:01:03" }, { "title": "Pikachu", "author": "TGalvez", "profilePictureUrl": "", "frontImageUrl": "images/2023/pikachu-front.png", "backImageUrl": "images/2023/pikachu-back.png", "description": "For all Pokemon players out there, we bring you Pik…achooo! Bless you!", "specialInstructions": "", "solderingInstructions": "Please visit https://minibadges.zevlag.com/buildguides/Zevlag-Minibadges-2023.pdf for the most updated and prettiest presentation of these instructions.\n\nASSEMBLY INSTRUCTIONS:\n- Begin on the Back side.\n- LED Direction indicators are on the image above, and on the board with icons.\n- Solder the 3 LEDs first.\n D1 = 1206 Red LEDs\n D2, D3 = 0805 Yellow LED\n- Solder the 2 resistors next.\n R1 = 100 Ω (1206) for Red LEDs\n R2 = 75 Ω (1206) for Yellow LED\n- Solder the 4x 2-Position headers on the Front side.\n- For the best illumination effect cover the openings on the back, including LEDs, with 2 separate globs of hot glue.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Z3ThunderKitty and tell her your favorite Pokemon Character.", "rarity": "Rare", "timestamp": "10/2/2023 8:03:04" }, { "title": "Hack Bus Front #1", "author": "CompuDoc & SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/hack-bus-front-1-front.png", "backImageUrl": "images/2023/hack-bus-front-1-back.png", "description": "1 of 3 Standard Badges that make a school bus for hackers it is designed to be expandable changeable and more sections will come in the future the front and back may be packaged together there are only 30 of each section this year", "specialInstructions": "", "solderingInstructions": "Instructions will be posted to GitHub https://github.com/CompuDocUt/SaintConMinibadges", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me or Ask for one", "rarity": "Super Rare", "timestamp": "10/2/2023 8:19:31" }, { "title": "Hack Bus Middle #2", "author": "CompuDoc & SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/hack-bus-middle-2-front.png", "backImageUrl": "images/2023/hack-bus-middle-2-back.png", "description": "2 of 3 Standard Badges that make a school bus for hackers it is designed to be expandable changeable and more sections will come in the future the front and back may be packaged together there are only 30 of each section this year", "specialInstructions": "", "solderingInstructions": "Instructions will be found on Git Hub https://github.com/CompuDocUt/SaintConMinibadges", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me or Ask for one", "rarity": "Super Rare", "timestamp": "10/2/2023 8:25:15" }, { "title": "Hack Bus Back #3", "author": "CompuDoc & SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2023/hack-bus-back-3-front.png", "backImageUrl": "images/2023/hack-bus-back-3-back.png", "description": "3 of 3 Standard Badges that make a school bus for hackers it is designed to be expandable changeable and more sections will come in the future the front and back may be packaged together there are only 30 of each section this year", "specialInstructions": "", "solderingInstructions": "Instructions will be found on GitHub https://github.com/CompuDocUt/SaintConMinibadges", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me or Ask for one", "rarity": "Super Rare", "timestamp": "10/2/2023 8:29:39" }, { "title": "Lego", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/lego-front.png", "backImageUrl": "images/2023/lego-back.png", "description": "This is my personal LEGO minibadge for fans of Lego. Backlit and beautiful", "specialInstructions": "", "solderingInstructions": "Simple SMD LED install", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Jup1t3r while he is at the Badge Life Community Booth, and while supplies last.", "rarity": "Uncommon", "timestamp": "10/2/2023 10:54:49" }, { "title": "Apple M2", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/apple-m2-front.png", "backImageUrl": "images/2023/apple-m2-back.png", "description": "As an Apple Product fan and evangelist, I figured we'd upgrade the processing power of the MiniBadge Board this year with custom \"who knows what really goes on in there\" silicon.", "specialInstructions": "", "solderingInstructions": "Just needs Header Pins", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Jup1t3r while at the Badgelife Booth", "rarity": "Rare", "timestamp": "10/2/2023 10:58:06" }, { "title": "Vote for Pedro", "author": "Codexicon", "profilePictureUrl": "", "frontImageUrl": "images/2023/vote-for-pedro-front.png", "backImageUrl": "images/2023/vote-for-pedro-back.png", "description": "Standard Vote for Pedro bade for Napoleon Dynamite fans.", "specialInstructions": "", "solderingInstructions": "Standard SMD mounting.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Codexicon around the conference.", "rarity": "Rare", "timestamp": "10/2/2023 11:04:19" }, { "title": "DEFCON Badge", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/defcon-badge-front.png", "backImageUrl": "images/2023/defcon-badge-back.png", "description": "As a fan of DEFCON, Im giving this away to anyone who has NEVER BEEN to DEFCON.", "specialInstructions": "", "solderingInstructions": "Standard SMD Soldering", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Jup1t3r while he is at the BadgeLife Booth, and let him know that you have Never been to DEFCON and need encouragement to go at least once.", "rarity": "Rare", "timestamp": "10/2/2023 11:12:33" }, { "title": "Flipper Badge", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/flipper-badge-front.png", "backImageUrl": "images/2023/flipper-badge-back.png", "description": "Flipper Badge", "specialInstructions": "", "solderingInstructions": "Standard SMD Soldering", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "You have to come to Jup1t3r's Epic Flipper Talk, and you will get one as supplies last.", "rarity": "Uncommon", "timestamp": "10/2/2023 11:14:07" }, { "title": "Iceman RFID Badge", "author": "Iceman", "profilePictureUrl": "", "frontImageUrl": "images/2023/iceman-rfid-badge-front.png", "backImageUrl": "images/2023/iceman-rfid-badge-back.png", "description": "This badge will encourage you to get your RFID on! And to meet me: \"The Iceman\"", "specialInstructions": "", "solderingInstructions": "Standard SMD Soldering", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Iceman around the conference event, introduce yourself, and request one.", "rarity": "Rare", "timestamp": "10/2/2023 11:17:19" }, { "title": "JLS3 Badge", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/jls3-badge-front.png", "backImageUrl": "images/2023/jls3-badge-back.png", "description": "This is a tribute badge to one of the Best Mentors of my life, and wonderful friend.", "specialInstructions": "", "solderingInstructions": "Standard SMD Soldering", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Get this badge from JLS3. He usually hangs out around the Education Security Community", "rarity": "Rare", "timestamp": "10/2/2023 11:19:53" }, { "title": "Neopixel Matrix", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/neopixel-matrix-front.png", "backImageUrl": "images/2023/neopixel-matrix-back.png", "description": "If you have one, you will know why.", "specialInstructions": "", "solderingInstructions": "These badges will come pre-assembled", "solderingDifficulty": "Stupid Hard", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "These badges are NOT available publicly, they are GIVEN to people for their service to the Community", "rarity": "Super Rare", "timestamp": "10/2/2023 11:23:01" }, { "title": "Trooper Badge", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/trooper-badge-front.png", "backImageUrl": "images/2023/trooper-badge-back.png", "description": "As a Star Wars Fan, I figured that it would be good to continue the roll-out of the next character, a Storm Trooper.", "specialInstructions": "", "solderingInstructions": "Standard SMD soldering", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Jup1t3r while he is at BadgeLife Booth, and ask for one.", "rarity": "Uncommon", "timestamp": "10/2/2023 11:28:01" }, { "title": "Wookie Badge", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/wookie-badge-front.png", "backImageUrl": "images/2023/wookie-badge-back.png", "description": "As a Star Wars Fan, I have created a Masterpiece on a PCB. Introducing the short-wookie Badge", "specialInstructions": "", "solderingInstructions": "Standard SMD soldering", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "These Badges are given out to people who contribute to the Community and to SAINTCON. They are not publicly available.", "rarity": "Super Rare", "timestamp": "10/2/2023 11:31:07" }, { "title": "UETN Sponsor Badge", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/uetn-sponsor-badge-front.png", "backImageUrl": "images/2023/uetn-sponsor-badge-back.png", "description": "UETN is a fundamental partner to SAINTCON and it's origins.", "specialInstructions": "", "solderingInstructions": "Standard SMD soldering", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Sponsor", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find a UETN employee and ask for one.", "rarity": "Rare", "timestamp": "10/2/2023 11:33:48" }, { "title": "MicroBadge", "author": "Zodiak", "profilePictureUrl": "", "frontImageUrl": "images/2023/microbadge-front.png", "backImageUrl": "images/2023/microbadge-back.png", "description": "We're going Micro with this personal MicroBadge from Zodiak", "specialInstructions": "", "solderingInstructions": "STandard SMD soldering", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Zodiak and ask for one of these tiny things.", "rarity": "Rare", "timestamp": "10/2/2023 11:38:12" }, { "title": "Marvin the Martian", "author": "Berly", "profilePictureUrl": "", "frontImageUrl": "images/2023/marvin-the-martian-front.png", "backImageUrl": "images/2023/marvin-the-martian-back.png", "description": "Marvin the Martian", "specialInstructions": "", "solderingInstructions": "Standard SMD soldering", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Berly around the conference center and get one from her!", "rarity": "Rare", "timestamp": "10/2/2023 11:43:54" }, { "title": "Dino-Jump Badge", "author": "Berly", "profilePictureUrl": "", "frontImageUrl": "images/2023/dino-jump-badge-front.png", "backImageUrl": "images/2023/dino-jump-badge-back.png", "description": "For those of you who like to mash keys when the internet is not working!!! You know who you are.", "specialInstructions": "", "solderingInstructions": "Standard SMD Soldering", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Berly around the conference and ask for one.", "rarity": "Rare", "timestamp": "10/2/2023 11:47:42" }, { "title": "Chunk Loves SAINTCON Badge", "author": "Chunk", "profilePictureUrl": "", "frontImageUrl": "images/2023/chunk-loves-saintcon-badge-front.png", "backImageUrl": "images/2023/chunk-loves-saintcon-badge-back.png", "description": "Inspired by the Goonies, and the origin of my handle, this fan art badge is my bade of choice this year.", "specialInstructions": "", "solderingInstructions": "Standard SMD soldering", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Chunk during the conference, usually hiding in a network closet.", "rarity": "Rare", "timestamp": "10/2/2023 11:50:20" }, { "title": "PALI 2023", "author": "Pali (Bryce Fox)", "profilePictureUrl": "", "frontImageUrl": "images/2023/pali-2023-front.jpg", "backImageUrl": "images/2023/pali-2023-back.jpg", "description": "This mini-badge features a symbol that represents my hacker handle with an LED that shines through the hole in the badge.", "specialInstructions": "", "solderingInstructions": "1 through hole 3mm LED where the LED stick into the hole in the badge from the back and then has bent over legs that connect to D1 surface pads. The long leg attaches to the pad that has LONG pointing to it.\n1 SMD style (10 ohm) resistor that connects to the R1 pads where the orientation will not matter.\nThere is a SOLID / BLINK solder blob switch JP1 where you will have to bridge two of the three switch pads with a solder blob to define the LED behavior.\nMost LEDs (UV flicker or Diffused Multicolor slow rotation) included with the badge will look nicer with the SOLID setting.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade me something I don't already have. That will usually be a non-SAINTCON official mini-badge. I am the tall committee member who runs the SAINTCON Store.", "rarity": "Rare", "timestamp": "10/2/2023 13:10:12" }, { "title": "CIRCUIT HACKING COMMUNITY MINIBADGE", "author": "Hamster", "profilePictureUrl": "", "frontImageUrl": "images/2023/circuit-hacking-community-minibadge-front.png", "backImageUrl": "images/2023/circuit-hacking-community-minibadge-back.png", "description": "In the Circuit Hacking Community, we will help you learn the design of digital circuits, and how to use tools and processes to decode the protocols common to modern devices.\n\nThere is an entire world of hardware to explore. We will make a deep-dive into the hacking of circuits available to all attendees of SAINTCON.", "specialInstructions": "", "solderingInstructions": "Visit our community for instructions!", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come and participate!", "rarity": "Uncommon", "timestamp": "10/2/2023 16:57:09" }, { "title": "Biohacking Community", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/biohacking-community-front.png", "backImageUrl": "images/2023/biohacking-community-back.png", "description": "Biohacking and Healthcare Hacking Community", "specialInstructions": "", "solderingInstructions": "Standard SMD soldering, but pay attention to the direction of the LED because it is not labeled on the back.", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Community", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come visit a Biohacking representative in the Healthcare Hacking Community", "rarity": "Rare", "timestamp": "10/2/2023 21:23:32" }, { "title": "Kids Night Attendee Badge", "author": "VIP", "profilePictureUrl": "", "frontImageUrl": "images/2023/kids-night-attendee-badge-front.png", "backImageUrl": "images/2023/kids-night-attendee-badge-back.png", "description": "This is the Kids Night gamer badge", "specialInstructions": "", "solderingInstructions": "Put the BLUE LED on the Left Side, and the Red LED on the Right Side. They can either be on the front, or on the back. If placed on the back, you may want to bend the LED around to face the game controller.\n\nResistors: 10Ohm goes on the BLUE side 68Ohm goes on the RED side. The LEDs are marked with the color to help.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Event", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "This badge is given to all Family Night attendees", "rarity": "Common", "timestamp": "10/2/2023 21:28:49" }, { "title": "Supertechguy Badge", "author": "Supertechguy", "profilePictureUrl": "", "frontImageUrl": "images/2023/supertechguy-badge-front.png", "backImageUrl": "images/2023/supertechguy-badge-back.png", "description": "The personal Minibadge for Supertechguy", "specialInstructions": "", "solderingInstructions": "Please pay close attention to the LED direction on the back because it is not well marked due to the way the board was made.", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find Supertechguy at the conference and ask him about the pink unicorn story. Don't leave till he tells you about it.", "rarity": "Rare", "timestamp": "10/2/2023 21:34:40" }, { "title": "White or Black Hat?", "author": "YodaMaster", "profilePictureUrl": "", "frontImageUrl": "images/2023/white-or-black-hat-front.png", "backImageUrl": "images/2023/white-or-black-hat-back.png", "description": "Inspired by spy vs spy and the concept of white hat hackers and black hat hackers. Using a jumper you can switch between being a white hat hacker or a black (uv led) hat hacker. Badge comes in white solder mask with black silkscreen or black solder mask with white silkscreen", "specialInstructions": "", "solderingInstructions": "Use single pad method to solder on surface mount components\nLED that appears yellowish is the white one the other is UV (watch diagram anodes for LEDs are towards the center\nsolder short side of 3 pin header to minibadge. Hack it any way you want (front, back, in, or out) so that you can use the included jumper to pick which light you want lit.\nsolder on the 4- 2 pin headers", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade or just ask me.", "rarity": "Uncommon", "timestamp": "10/2/2023 21:35:36" }, { "title": "PC Load Letter Badge", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2023/pc-load-letter-badge-front.png", "backImageUrl": "images/2023/pc-load-letter-badge-back.png", "description": "You need to watch Office Space!", "specialInstructions": "", "solderingInstructions": "Standrd SMD soldering", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come and find Jup1t3r while he is at the Badgelife Booth to get one of these.", "rarity": "Rare", "timestamp": "10/2/2023 21:42:08" }, { "title": "University of Idaho", "author": "YodaMaster", "profilePictureUrl": "", "frontImageUrl": "images/2023/university-of-idaho-front.png", "backImageUrl": "images/2023/university-of-idaho-back.png", "description": "UI sponsored BSides - Idaho Falls this year and to celebrate/thank them for the sponsorship I created this badge with the UI I-Bar logo on it.", "specialInstructions": "", "solderingInstructions": "use single pad method to solder on surface mount components. \nLook at diagram anode of LEDs goes towards the top\nsolder on the 4 - 2 pin headers\npay attention to text on back for direction. LEDs won't light up if badge is upside down\nHot glue on LEDs and exposed substrate makes the I-bar glow better", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Ask me, trade with me, or give me your bestest most proud \"Go Vandals!\" cheer.", "rarity": "Uncommon", "timestamp": "10/2/2023 22:05:02" }, { "title": "FoxyCorn", "author": "MiaBiaLia", "profilePictureUrl": "", "frontImageUrl": "images/2023/foxycorn-front.png", "backImageUrl": "images/2023/foxycorn-back.png", "description": "MiaBiaLia loves foxes and unicorns so she decided she wanted a minibadge to display both", "specialInstructions": "", "solderingInstructions": "Mount LED on the back and bend it over so it is in the middle of the badge.\nAnode (short end of LED goes in the square hole)\nsolder on top and snip legs off\nsolder on the 4 - 2pin headers", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "MiaBiaLia will be at family night. She would love to trade or you can just ask her for one. YodaMaster may have some on hand Friday as well", "rarity": "Rare", "timestamp": "10/2/2023 22:21:28" }, { "title": "Cybersecurity and Network Management - HackerWaldo Cutout", "author": "Weber State Univeristy - kfeuz", "profilePictureUrl": "", "frontImageUrl": "images/2023/cybersecurity-and-network-management-hackerwaldo-cutout-front.png", "backImageUrl": "images/2023/cybersecurity-and-network-management-hackerwaldo-cutout-back.png", "description": "This is an official minibadge of the Weber State University Cybersecurity and Network Management Program. It features our mascot Waldo the Wildcat in his hacking gear.", "specialInstructions": "", "solderingInstructions": "Solder the 470 ohm resistors on R1 and R2. \nSolder the 100 ohm resistor on R3. \nSolder the green leds on D1 and D2.\nSolder the white led on D3", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "We will be handing these out like candy. We will try to have a stash available at the soldering tables as well.", "rarity": "Uncommon", "timestamp": "10/2/2023 22:37:24" }, { "title": "Cybersecurity and Network Management - HackerWaldo Square", "author": "Weber State University - TheTrollGod", "profilePictureUrl": "", "frontImageUrl": "images/2023/cybersecurity-and-network-management-hackerwaldo-square-front.png", "backImageUrl": "images/2023/cybersecurity-and-network-management-hackerwaldo-square-back.png", "description": "This is an official minibadge of the Weber State University Cybersecurity and Network Management Program. It features our mascot Waldo the Wildcat in his hacking gear.", "specialInstructions": "", "solderingInstructions": "Solder the 100 ohm resistors to R1 and R2\nSolder the red leds to D1 and D2", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "We will be handing these out like candy. We will also hopefully have a stash at the soldering tables.", "rarity": "Uncommon", "timestamp": "10/2/2023 22:41:14" }, { "title": "RADICL", "author": "YodaMaster", "profilePictureUrl": "", "frontImageUrl": "images/2023/radicl-front.png", "backImageUrl": "images/2023/radicl-back.png", "description": "Inspired by the logo for University of Idaho's Reconfigurable Attack Defend Instructional Computing Laboratory (RADICL). RADICL allows students to be on the red team or the blue team depending on the exercise... this badge's switch allows you to choose the red team or the blue team", "specialInstructions": "", "solderingInstructions": "use single pad method to solder on surface mount components\nLED with blue paint on the package goes with resistor with blue marking (Ie. D1 and R1)\nLED with red goes with resistor with red marking (D2 and R2)\nsolder switch on to the bottom of the badge 2 holes in board should keep it from moving and align switch to the edge of the mini badge\nsolder on the 4- 2pin headers\nhot glue over LEDs and exposed substrate evens out the light and makes this badge pop", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Ask me or trade with me", "rarity": "Rare", "timestamp": "10/2/2023 22:43:33" }, { "title": "Attendee Minibadge (and other badge game minibadges)", "author": "MK Factor", "profilePictureUrl": "", "frontImageUrl": "images/2023/attendee-minibadge-and-other-badge-game-minibadges-front.png", "backImageUrl": "images/2023/attendee-minibadge-and-other-badge-game-minibadges-back.png", "description": "This is the official attendee minibadge for 2023. It's part of the badge game and has an EEPROM on the back so that the badge can identify it. There isn't an LED since the badge itself has RGB LEDs to illuminate the game minibadges. For all the official game minibadges, you'll only need to solder the pins. The EEPROM is already soldered and programmed. There are many other game-related minibadges that are assembled the same way.", "specialInstructions": "", "solderingInstructions": "Solder the pins to the back of the minibadge. When inserted into the badge, the RGB LED on the badge should light up indicating that it can read the EEPROM on the minibadge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "This one is included with the badge, but there are lots of other game-related minibadges that you can only get by playing the badge game!", "rarity": "Common", "timestamp": "10/3/2023 10:20:33" }, { "title": "Compukidmike - Sunset", "author": "CompuKidMike", "profilePictureUrl": "", "frontImageUrl": "images/2023/compukidmike-sunset-front.png", "backImageUrl": "images/2023/compukidmike-sunset-back.png", "description": "I wanted to try something different this year so I used a 4-layer PCB. The idea was to get multiple layers of mountains and background for the sunset. Unfortunately the PCB diffuses the light too much to get the desired effect. I may try again with a thinner PCB to get the effect I want.", "specialInstructions": "", "solderingInstructions": "Solder the LED and resistor on the back. The LED is reverse-mount, so it shines directly into the PCB. It has a notched corner that you align with the triangle on the board.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find me and ask for one! Once they're gone, that's it!", "rarity": "Uncommon", "timestamp": "10/3/2023 10:31:28" }, { "title": "Butterfly", "author": "Mike's Wife", "profilePictureUrl": "", "frontImageUrl": "images/2023/butterfly-front.png", "backImageUrl": "images/2023/butterfly-back.png", "description": "I wanted to use a flex PCB and came up with the butterfly. It uses a large resistor and through-hole LEDs to hold the flex PCB to the minibadge board.", "specialInstructions": "", "solderingInstructions": "Solder the pins to the minibadge board first. Then align the flex PCB on top and put the resistor legs through the flex PCB and into the minibadge board. This will hold the two PCBs together. Do the same with the LEDs. Place them partway through the top of the flex PCB and into the minibadge board, bending the LEDs down to form the butterfly's antennae. Once you have things aligned, solder the resistor and LEDs.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find me and ask for one!", "rarity": "Uncommon", "timestamp": "10/3/2023 10:43:00" }, { "title": "Unstoppable", "author": "Honki & Mike's Wife", "profilePictureUrl": "", "frontImageUrl": "images/2023/unstoppable-front.png", "backImageUrl": "images/2023/unstoppable-back.png", "description": "I used to suffer from short arms, but now that I've got my grabber claws I'm unstoppable!", "specialInstructions": "", "solderingInstructions": "Solder the resistor and two red LEDs on the back.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Ask for one. Trades are always appreciated.", "rarity": "Rare", "timestamp": "10/3/2023 10:51:59" }, { "title": "Bronco Badge", "author": "BP & klipper", "profilePictureUrl": "", "frontImageUrl": "images/2023/bronco-badge-front.png", "backImageUrl": "images/2023/bronco-badge-back.png", "description": "The rear-view of a classic off-roading vehicle reborn. Red LED as tail-lights and the iconic bucking horse logo on the back. Since I love my Bronco, thought it'd be fun to have a minibadge of it. Special thanks to @klipper and @spamwizard for design assistance.", "specialInstructions": "", "solderingInstructions": "Solder the resistor on the back, and the LED's on the front. Watch the silkscreen for polarity.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come find me and trade with me! This is my second SAINTCON and still meeting people / learning names and faces so come swap a cool off-roading story with me, or talk about your favorite vehicle you've driven. Or just come hand me a badge and I'll give you one back...or come ask nicely. Or bring me icecream. Really, anything.", "rarity": "Uncommon", "timestamp": "10/7/2023 19:10:21" }, { "title": "Spooky, Scary Skeletons", "author": "DistinctM1nd", "profilePictureUrl": "", "frontImageUrl": "images/2023/spooky-scary-skeletons-front.png", "backImageUrl": "images/2023/spooky-scary-skeletons-back.png", "description": "Who wouldn't want a spooky, scary skeletons minibadge!", "specialInstructions": "", "solderingInstructions": "Start on the back of the main board. Solder D1 (0805) and D2 (0805) following the LED orientation in the guide. Solder R1 (0805). Solder the 2.54mm 2 pin female header for the add-on. Solder the 2.54mm male headers to the corners of the badge. \n\nFor the add-on, solder the resistor (0603) to R1 and the led (0402) to D1. Solder the 2.54mm 2 pin male header and connect to the main badge. \n\nOptional but recommended - apply hot glue to cover the moon and 2 LEDs on the back of the main board to evenly disperse the light from the LEDs.", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade with me", "rarity": "Super Rare", "timestamp": "10/7/2023 20:38:19" }, { "title": "Hal9000", "author": "David Bowman - Hollyhacker", "profilePictureUrl": "", "frontImageUrl": "images/2023/hal9000-front.png", "backImageUrl": "images/2023/hal9000-back.png", "description": "It’s a little known fact that the character name of the primary astronaut in A Space Odyssey 2001 is David Bowman …", "specialInstructions": "", "solderingInstructions": "Assembly Video \nhttp://fireboltservices.weebly.com/minbadges.html", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Trade", "rarity": "Super Rare", "timestamp": "10/7/2023 21:30:48" }, { "title": "Bionic Bruins Badge", "author": "Bruin ETE", "profilePictureUrl": "", "frontImageUrl": "images/2023/bionic-bruins-badge-front.png", "backImageUrl": "images/2023/bionic-bruins-badge-back.png", "description": "This is the official logo of the Twin Falls Bionic Bruins robotics team. It features a 3mm THT LED that will act as an eye. Shout out to Mister X for helping get this minibadge designed!", "specialInstructions": "", "solderingInstructions": "• Begin on the front side first.\n• Solder the LED first, with the short end going through the square hole and solder the connection on the back.\n• Switch to the back and solder the resistor using single-pad method for hand soldering.\n• Solder the 4x 2-Position headers, with the Bionic Bruins artwork facing out.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Because of the limited stock, you'll need to talk to Mister X about getting one.", "rarity": "Super Rare", "timestamp": "10/8/2023 8:40:09" }, { "title": "Shodan", "author": "SpamWizard & Zodiak", "profilePictureUrl": "", "frontImageUrl": "images/2023/shodan-front.png", "backImageUrl": "images/2023/shodan-back.png", "description": "Maybe this minibadge is the only thing you own that has been on Shodan. Probably not.", "specialInstructions": "", "solderingInstructions": "LED where the LEDs go. Resistor where the resistors go. Pins where the pins go.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Find zodiak. Come with a trade, a favor, or Chocolate milk. If you can't do that, maybe a good joke or a small ditty performance will do.", "rarity": "Rare", "timestamp": "10/11/2023 21:54:45" }, { "title": "MicroBadge #2", "author": "Zodiak's idea. Shifty's execution.", "profilePictureUrl": "", "frontImageUrl": "images/2023/microbadge-2-front.png", "backImageUrl": "images/2023/microbadge-2-back.png", "description": "A variant of the other MicroBadge. Though slightly less micro.", "specialInstructions": "", "solderingInstructions": "Due to quantity, these don't have all the parts. I have some parts, but waaaaaaaay more PCB's than I have parts. You can buy any old 1206 LED and 1206 resistor (probably in the 50-200 ohm range).\n\nOnce you have the parts, put the resistor on, then the LED. Once you have that, test fit the header pins (AKA: DO NOT SOLDER UNTIL YOU KNOW THE CORRECT ORIENTATION), and put it in your badge. It will work in the top left corner, or either of the right corners, but you have to manipulate the orientation of the microbadge depending on where you put it. Consider this an experiment. You can't break things, so play with it. Get it to light in the spot you desire. Once you are happy, solder the headers and enjoy.", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Personal", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "Come find Zodiak. He has piles of these...", "rarity": "Common", "timestamp": "10/11/2023 22:01:33" }, { "title": "Make it Bigger", "author": "Honki & Xanadu2600", "profilePictureUrl": "", "frontImageUrl": "images/2023/make-it-bigger-front.jpg", "backImageUrl": "images/2023/make-it-bigger-back.jpg", "description": "A familiar phrase repeated at check-in as people show their QR codes that just aren't big enough to scan well... now made into a minibadge.", "specialInstructions": "", "solderingInstructions": "Solder to look like the image. \nUse fine solder for the 8 pin IC and watch pin 1 (looking at the back of the board it is top left)\nWatch markings for the LEDs negative goes to the top for the closed and half open hand and towards the bottom for the open hand\nOrientation doesn't matter for the resistors but the 200k ohm goes on the right and the 100k ohm goes above the IC.\nA bodge wire needs to be soldered from the top of the 200k ohm resistor to the positive side of the led on the open hand\nFor best effect: side mount the LEDs with the lens pointing to the hand and use the red LED for the closed hand, yellow in the middle and green for the fully open hand.", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Event", "conferenceYear": "2023", "boardHouse": "", "howToAcquire": "This very rare badge can be obtained by convincing someone at the registration check in tables to part with one", "rarity": "Rare", "timestamp": "10/23/2023 21:53:36" } ]