[ { "title": "PEOPLE BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/people-badge-front.png", "backImageUrl": "images/2022/people-badge-back.png", "description": "The ATTENDEE, STAFF, VOLUNTEER, SPEAKER\nMinibadge for people. This Minibadge comes in a variety of\ncolors but you only get the one for your status level.\nThis MiniBadge is given to you based on your involvement level in\nthe conference. Everyone gets an ATTENDEE Badge.\nThis MiniBadge looks amazing, but is a little technical on how to\nput it together.", "specialInstructions": "", "solderingInstructions": "• Building this badge is NOT HARD, but does require you to follow precise\ninstructions. To make it easier, I have made a video on how to create this badge.\n• Please follow the instructions in the Online Video by scanning this QR CODE:", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Common", "timestamp": "" }, { "title": "APPSEC COMMUNITY BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/appsec-community-badge-front.png", "backImageUrl": "images/2022/appsec-community-badge-back.png", "description": "The AppSec Community Minibadge has the classic Wasp symbol\nwhich is a nod to the OWASP application security framework.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED Direction indicators are on the image to the left.\n• Solder the two LEDs first, using the single-pad method for hand soldering.\n• Solder the Resistor using the same single-pad method for hand soldering.\n• Solder the 4x 2-Position headers, with the Wasp artwork facing out.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "This MiniBadge can be obtained by interacting with the AppSec Community folks at their booth.", "rarity": "Common", "timestamp": "" }, { "title": "CIRCUIT ASSEMBLY BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/circuit-assembly-badge-front.png", "backImageUrl": "images/2022/circuit-assembly-badge-back.png", "description": "Circuit Assembly, is the new name for the area where we do all of\nthe soldering at SAINTCON. This badge is super simple to\nassemble.\nThis badge has both Through-hole (THT) and Surface-Mount\n(SMD) components.\nLED ORIENTATION WARNING\nNOTE: This LED has poor markings for\npolarity. Please reference the image\nabove to ensure you have the LED\ninstalled the right direction.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the Resistors by placing them through the holes on either side of the Turtle\nimage, with the resistors on the front of the badge.\n• Solder the Jumper at the bottom of the board, bridging EITHER the SOLID or\nBLINK side, Never Solder across all three.\nBAD\nNO BLINK SOLID\nJUMPER JUMPER JUMPER JUMPER\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "You can acquire this MiniBadge by showing off something you soldered to the folks running this community on the stage tables.", "rarity": "Common", "timestamp": "" }, { "title": "HACK MINIBADGES", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/hack-minibadges-front.png", "backImageUrl": "images/2022/hack-minibadges-back.png", "description": "The HACK minibadges are a set of\n4 made up of each letter in the\nword HACK. For this year they will\nbe given out as a set.\nJup1t3r may ask you about your\nfirst ever real hack to earn this set\nof Minibadges. DIFFICULTY: RARITY:\nINTERMEDIATE RARE", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• Each LED has a Black-Dot to mark the Cathode. Attach the LEDs using the\nsingle-pad hand soldering method. 4 LEDs per badge.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To obtain this set of Minibadges, visit the BadgeLife community booth while Jup1t3r it present and behind the table. This will occur several times during the conference event, but is not scheduled specifically.", "rarity": "Rare", "timestamp": "" }, { "title": "HACKERS CHALLENGE BADGE", "author": "Zevlag", "profilePictureUrl": "", "frontImageUrl": "images/2022/hackers-challenge-badge-front.png", "backImageUrl": "images/2022/hackers-challenge-badge-back.png", "description": "Designed by Zevlag, the Hackers Challenge Minibadge is a\ncommon badge to find at SAINTCON. You can obtain one by\ninteracting with one of the Game Masters for the Hackers\nChallenge game. They MAY make you solve at least one puzzle\nto earn one, but then again, maybe not.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• Attach the non-colored LED on the back side first. (D1) Use the single-pad\nmethod for hand soldering.\n• Using the same method, attach the resistors defined here:\n• Non-Colored Resistor to R1\n• Red-Colored Resistor to R2\n• Blue-Colored Resistor to R3\n• On the FRONT of the Minibadge, attach the remaining LEDs as defined here:\n• Red-Colored LED to D2\n• Blue-Colored LED to D3\n• NOTE: As an alternative, you may choose to turn the LEDs upside-down. The\ndesigner recommends this option if you are able to do it. (Advanced)\n• Solder the 3x 2-Position headers.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Common", "timestamp": "" }, { "title": "HAK-IN-THE-BOX BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/hak-in-the-box-badge-front.png", "backImageUrl": "images/2022/hak-in-the-box-badge-back.png", "description": "HACK-IN-THE-BOX or HAK-IN-THE-BOX is an unofficial event\nthat partners with SAINTCON each year to offer more after-hours\nactivities for conference attendees.\nThis MiniBadge offers reverse-mount LEDs that can be a little\ndifficult to solder. Some patience will be required.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\nLED ORIENTATION\n• LED direction is illustrated to the right >>>>>.\nTHIS END\n• Solder the LEDs first, using the single-pad method TO TOP\nfor hand soldering.\n• Solder the resistors, using the single-pad method for\nhand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this MiniBadge, you will need to visit the Hack-in-the-box event.", "rarity": "Uncommon", "timestamp": "" }, { "title": "HARDWARE HACKING BADGE", "author": "Hamster", "profilePictureUrl": "", "frontImageUrl": "images/2022/hardware-hacking-badge-front.png", "backImageUrl": "images/2022/hardware-hacking-badge-back.png", "description": "This is the badge for the Hardware Hacking Community, and is\ndesigned to help teach how to solder and how basic analog\ncircuits work.", "specialInstructions": "", "solderingInstructions": "• Leave the badges together as a panel until the end. Start on the top side.\n• Take your stick of sockets, and break them up into: qty two-pin sockets, and 22,\none-pin sockets.\n• Next place an index card or other stiff item across the top of the panel and\ncarefully flip it over.\n• Solder each of the sockets.\n• Next, install the other components: Please not polarity of the capacitors. Please\nalso note the DOT on the 555 timer, and Resistors should be installed “standing\nup”.\n• Attach each of the 2-pin headers.\n• Break up the board and start playing with circuits.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this Minibadge, come and visit the Hardware Hacking Community area.", "rarity": "Common", "timestamp": "" }, { "title": "HEALTHCARE COMMUNITY BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/healthcare-community-badge-front.png", "backImageUrl": "images/2022/healthcare-community-badge-back.png", "description": "The Healthcare Hacking Community is a new addition to\nSAINTCON for 2022. Learn about Medical Device Security and\nthe challenges of security in healthcare.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.\n• For a better lighting effect, you can use HOT GLUE to cover the LEDs and the\nunmasked area on the back of the Minibadge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this Minibadge, you will need to interact with the folks at the Healthcare hacking Community Booth.", "rarity": "Common", "timestamp": "" }, { "title": "HOMELABS MINIBADGE", "author": "bfcoder & Jup1t3r & klipper & v0rtex & yukia", "profilePictureUrl": "", "frontImageUrl": "images/2022/homelabs-minibadge-front.png", "backImageUrl": "images/2022/homelabs-minibadge-back.png", "description": "HomeLabs is a new community to SAINTCON in 2022. They will\nprovide instruction and resources for helping you develop a\nHome Lab with the goal to further develop your skillsets in an\narea you want to develop.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED direction indicators are on the image above. (Marked in Blue)\n• Solder the resistors first, using the single-pad method for hand soldering.\n• Each resistor is paired with the color of LED. The pairing matters!\n• Solder the 1ohm on the left side for the blue LED.\n• Solder the 62ohm on the right side for the red and green LED’s.\n• Solder the LED’s using the single-pad method for hand soldering.\n• The red LED is designed to shine away from the badge and reflect back\nto the eyes.\n• The blue and green LED’s are designed to shine directly through the PCB\n• Solder the 3x 2-position headers.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these MiniBadges, you just need to visit the HomeLabs Community Both and interact.", "rarity": "Common", "timestamp": "" }, { "title": "HOMELABS CAT6 MINIBADGE", "author": "bfcoder & klipper & v0rtex & yukia", "profilePictureUrl": "", "frontImageUrl": "images/2022/homelabs-cat6-minibadge-front.png", "backImageUrl": "images/2022/homelabs-cat6-minibadge-back.png", "description": "This Minibadge can be used as a simple Ethernet Cable Tester", "specialInstructions": "", "solderingInstructions": "FOR THE SOURCE BADGE\n• Start on the FRONT, by soldering the LEDs using\nthe single-pad soldering method.\n• On the reverse-side, solder the resistors using the\nsingle-pad soldering method.\nFOR BOTH BADGES:\n• Once all LEDs and Resistors are connected, gently\npress-to-fit the ethernet jack (careful to not bend\nthe pins against the board). Once press-fit, you\nmay solder each connection on the back side.\n• Then connect the header pins", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these Minibadge Sets, you must complete the Home Labs section of the Hackers Challenge contest.", "rarity": "Uncommon", "timestamp": "" }, { "title": "INFOBOOTH BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2022/infobooth-badge-front.png", "backImageUrl": "images/2022/infobooth-badge-back.png", "description": "Designed by SHIFTY, this badge is handed out by the InfoBooth.\nThe badge is available while supplies last.\nThey InfoBooth staff may require you to complete some task\nbefore getting one of these badges.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LED first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Uncommon", "timestamp": "" }, { "title": "IOT COMMUNITY MINIBADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/iot-community-minibadge-front.png", "backImageUrl": "images/2022/iot-community-minibadge-back.png", "description": "The IoT Community is where you can learn about the entire and\never-growing world of vulnerable things that exist on the internet.\nThis Minibadge can be acquired by interacting with the people\nrunning the IoT community booth in the expo space.\nWARNING: Component labels on this badge are a little\nconfusing, THE LED is on the TOP, the RESISTOR is on the\nBOTTOM. Don’t mess it up!", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LED first, using the single-pad method for hand soldering.\nNOTE: The LED is the TOP COMPONENT, (See Green Dot Above)\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Common", "timestamp": "" }, { "title": "LEADERSHIP BADGE", "author": "Handsomkab & Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/leadership-badge-front.png", "backImageUrl": "images/2022/leadership-badge-back.png", "description": "The Leadership Community is where we invite C-Level executives\nto come and participate in SAINTCON.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• Solder the LED so that it is connected on the back-side of the board, with a\nminimum of 1/2” standoff so the LED can be bent slightly inward.\n• Solder the resistor using the single-pad method for hand soldering.\n• After soldering, carefully bend the LED around until it is resting on the back of the\nboard as shown above.\n• Solder the 4x 2-Position headers.\n• For a better lighting effect, you can use HOT GLUE to cover the LEDs and the\nunmasked area on the back of the Minibadge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this badge, you need to participate in the Leadership Community", "rarity": "Uncommon", "timestamp": "" }, { "title": "LOCKPICKING BADGE", "author": "Redactd", "profilePictureUrl": "", "frontImageUrl": "images/2022/lockpicking-badge-front.png", "backImageUrl": "images/2022/lockpicking-badge-back.png", "description": "The Lock Picking area is where we teach that “Everything is\nvulnerable if you know how it works”. We believe that teaching\nsomeone how to pick locks, teaches them how to think outside\nthe box.", "specialInstructions": "", "solderingInstructions": "• Begin on the Front side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Turn the badge over.\n• Solder the resistor using the single-pad method for hand soldering.\n• CAREFULLY separate the springs. (They will get lost if you are not careful)\n• Insert one spring into each of the four positions to complete the circuit.\n• You MAY have to adjust the diameter of the spring to make a good contact.\n• If you lose a spring, there are a few extras at the Circuit Assembly Booth\n(while supplies last)\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these awesome Minibadges, please visit the Lock Picking Community. They MAY make you pick a lock to earn one, or they may just be handing them out. Just ask.", "rarity": "Common", "timestamp": "" }, { "title": "LOS SANTOS CHALLENGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/los-santos-challenge-front.png", "backImageUrl": "images/2022/los-santos-challenge-back.png", "description": "The Los Santos Escape challenge is one of the premiere lock-\npick and critical thinking escape contest at SAINTCON.\nTo acquire this MiniBadge, you either need to participate in, or\nobserve someone participating in the escape challenge. We\nencourage the direct participation however.\nThis Minibadge is simple to assemble.\nLED ORIENTATION WARNING\nNOTE: This LED has poor markings for\npolarity. Please reference the image\nabove to ensure you have the LED\ninstalled the right direction.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistors using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Common", "timestamp": "" }, { "title": "PACKET CAPTURE BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/packet-capture-badge-front.png", "backImageUrl": "images/2022/packet-capture-badge-back.png", "description": "Packet Capture badge is obtained from the Packet Capture\nCommunity booth.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 3x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Common", "timestamp": "" }, { "title": "PASSWORD CRACK BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/password-crack-badge-front.png", "backImageUrl": "images/2022/password-crack-badge-back.png", "description": "Password Cracking is an important technology to understand.\nTo acquire this MiniBadge, you need to interact with the people\nrunning the password cracking community booth.\nThe MiniBadge can be set to either BLINK or be SOLID. You can\nalso solder it to have YES LED, NO LED, or both LEDs on by\nsoldering the YES or NO jumpers in the center.", "specialInstructions": "", "solderingInstructions": "• Begin on the Front side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Turn the badge over, solder the resistors using the single-pad method for hand\nsoldering.\n• Solder the Jumper at the top of the board, bridging EITHER the SOLID or BLINK\nside, Never Solder across all three.\nBAD\nNO BLINK SOLID\nJUMPER JUMPER JUMPER JUMPER\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Common", "timestamp": "" }, { "title": "PRIVATE LTE BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/private-lte-badge-front.png", "backImageUrl": "images/2022/private-lte-badge-back.png", "description": "The Private LTE minibadge is a promotional badge for the use of\nLTE technology in private networks.\nD1", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• Begin by placing the LED through the hole emerging from the back side. Once in\nthe hole, rotate the LED so that the shorter leg of the LED is on the LEFT side\n• Bend the Short LED leg upward, and TRIM it so that it is only as long as needed\nto reach the LED pad marked RED above (SHORT SIDE GOES TO RED)\n• Bend the Long LED leg upward, and TRIM it so that it is only as long as needed\nto reach the LED pad marked BLUE above. (LONG SIDE GOES TO BLUE)\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 3x 2-Position headers.\nEDIS\nTALF", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this minibadge, you need to find the folks who are promoting this technology. They usually hang out in the Leadership Track.", "rarity": "Rare", "timestamp": "" }, { "title": "RED TEAM MINIBADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/red-team-minibadge-front.png", "backImageUrl": "images/2022/red-team-minibadge-back.png", "description": "The Red Team Community is where you can learn many of the\ntools and tactics of penetration testing, and even test your skills\nagainst real-life scenarios.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder either the BLINK or SOLID size of the Jumper depending on your\npreference.\nBAD\nNO BLINK SOLID\nJUMPER JUMPER JUMPER JUMPER\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this MiniBadge, you will need to visit the Red Team Community and interact with them there.", "rarity": "Common", "timestamp": "" }, { "title": "RFID/NFC Community Badge", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/rfidnfc-community-badge-front.png", "backImageUrl": "images/2022/rfidnfc-community-badge-back.png", "description": "Come learn about NFC and RFID Vulnerabilities. And we’ll give\nyou one of these cool MiniBadges while supplies last.", "specialInstructions": "", "solderingInstructions": "• Begin on the Front side first.\n• LED Direction indicators are on the image above.\n• Solder the LED first, using the single-pad method for hand soldering.\n• Solder the resistors using the single-pad method for hand soldering.\n• Affix the RFID Tag Sticker to the back-side of the MiniBadge.\nYou MAY have to trim it slightly along the edges\n• IMPORTANT: Complete the previous step before putting on the pin headers\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Common", "timestamp": "" }, { "title": "SCAVENGER HUNT BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/scavenger-hunt-badge-front.png", "backImageUrl": "images/2022/scavenger-hunt-badge-back.png", "description": "Play the Scavenger Hunt game, and you will get a Scavenger\nHunt MiniBadge.\nSimple Design", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Common", "timestamp": "" }, { "title": "SMD Challenge BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/smd-challenge-badge-front.png", "backImageUrl": "images/2022/smd-challenge-badge-back.png", "description": "This Badge is designed to challenge your SMD soldering skills,\nand/or teach you to use more advanced soldering tools.\nThere is a Solder Paste Stencil available at the Circuit Assembly\nadministration booth. This will make your efforts infinitely easier if\nyou want to use it.\nThis badge is acquired by purchasing it from the SAINTCON\nstore for $5 to cover the cost of components and special tools\nyou will borrow to make it work.", "specialInstructions": "", "solderingInstructions": "• Begin on the Front side first.\n• We highly recommend that you use the Solder Paste Stencil available in the\nCAC by asking the people running the area for help. You can alternatively hand\nsolder many of these components by hand if you want to attempt it.\n• PUT THE LEDS ON FIRST!\n• NOTE: The Golden Ratio curve acts as the NEGATIVE side of the circuit for every\nLED. Please orient them with the Cathode facing the curve.\n• LED Direction indicators are on the image above (Green Dots).\n• After attaching the LEDs, proceed to hand-solder the components on the back\nside.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Rare", "timestamp": "" }, { "title": "STORE MINIBADGe", "author": "Pali", "profilePictureUrl": "", "frontImageUrl": "images/2022/store-minibadge-front.png", "backImageUrl": "images/2022/store-minibadge-back.png", "description": "The Store is where you can go get ur Merch!", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LED first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this minibadge you need to purchase something from the store, while supplies last.", "rarity": "Uncommon", "timestamp": "" }, { "title": "LEARN 2 SOLDER BADGE", "author": "r0gu3bull3t", "profilePictureUrl": "", "frontImageUrl": "images/2022/learn-2-solder-badge-front.png", "backImageUrl": "images/2022/learn-2-solder-badge-back.png", "description": "To get this Minibadge, you will need to participate in the Learning\nto Solder presentation.", "specialInstructions": "", "solderingInstructions": "• Instructions to solder this badge will be given in the soldering class.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this Minibadge, you will need to participate in the Learning to Solder presentation.", "rarity": "Rare", "timestamp": "" }, { "title": "Tamper Evident BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/tamper-evident-badge-front.png", "backImageUrl": "images/2022/tamper-evident-badge-back.png", "description": "Tamper Evident badges are given out after interacting with the\nfolks at the Tamper Evident Contest booth.\nSimple Design", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Uncommon", "timestamp": "" }, { "title": "UNDISCLOSED BADGE", "author": "Sh33pr0ck", "profilePictureUrl": "", "frontImageUrl": "images/2022/undisclosed-badge-front.png", "backImageUrl": "images/2022/undisclosed-badge-back.png", "description": "The existence of this badge cannot be confirmed, but can also\nnot be denied. It is spoken of in whisper, and generally has\nsomething to do with thin metal sheets of aluminum.\nYou can obtain this badge (assuming it exists) by attending the\nmost exclusive event (assuming it exists) and participating (if\nthat’s even possible).\nThere is significant evidence that the TFHT Minibadge does exist,\nand the conspiracy is not a conspiracy, we have proof that with\nthe Minibadge is actually a tracker and serves to augment all\nfields of mind control, making it the most dangerous element of\nthis supposed “security conference”. We also discovered that\nthe way to start all of this process is to go to the following URL\nand prove yourself through a scenario: https://tfht.agency", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• D1 LED is a color-Changing LED (Arrow points to the Green-Dot marked above)\n• D2 LED is a solid Color LED\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistors using the single-pad method for hand soldering.\n• R1 is the PURPLE Resistor\n• R2 is the GREEN Resistor\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Rare", "timestamp": "" }, { "title": "VENT EVENT BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/vent-event-badge-front.png", "backImageUrl": "images/2022/vent-event-badge-back.png", "description": "The VENT event is the newest event at SAINTCON this year,\nallowing security professionals an opportunity to speak and tell\nstories “off the record”.\nNOTE: This badge as a Design Flaw! The Resistor needs to\nbe connected to GND at the top with a wire to work properly.\nWe caught this LATE, and didn’t have time to redo them. We\nleave it to YOU to “Hack it” properly.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder either the BLINK or SOLID size of the Jumper depending on your\npreference.\nBAD\nNO BLINK SOLID\nJUMPER JUMPER JUMPER JUMPER\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these MiniBadges, you will need to attend and participate in the VENT event.", "rarity": "Rare", "timestamp": "" }, { "title": "VAULT BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/vault-badge-front.png", "backImageUrl": "images/2022/vault-badge-back.png", "description": "The Vault is a physical security bypass challenge. This event is\nrun by JC and Snow from Snowfensive.\nThe Vault MiniBadge can be obtained by participating or\nobserving others participate in the Vault Challenge, and is handed\nout at the Vault Area.", "specialInstructions": "", "solderingInstructions": "• Begin on the Front side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Turn the badge over.\n• Solder the resistors using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Common", "timestamp": "" }, { "title": "WIDOW BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/widow-badge-front.png", "backImageUrl": "images/2022/widow-badge-back.png", "description": "The Widows of SAINTCON are primarily the women spouses of\nthe conference organizers of the conference. This Badge was\ndesigned to honor their efforts of being widowed for so much\ntime during the planning and execution of the conference.\nThis badge is not generally available, and is given to members of\nthe SAINTCON Widows group.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.\n• For a better lighting effect, you can use HOT GLUE to cover the LEDs and the\nunmasked area on the back of the Minibadge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Official", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Common", "timestamp": "" }, { "title": "ARCTIC WOLF MINIBADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/arctic-wolf-minibadge-front.png", "backImageUrl": "images/2022/arctic-wolf-minibadge-back.png", "description": "Arctic Wolf is one of our awesome sponsors. This badge is\ndesigned to oscillate between BLUE and ORANGE LED colors,\nbacklighting the silhouette wolf logo using the clock for the badge\nto drive the blinking.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED Direction indicators are on the image to the left.\n• Solder the two LEDs first, using the single-pad method for hand soldering.\nORANGE LED goes on the LEFT side.\nBLUE LED goes on the RIGHT side.\n• Solder the Resistors using the same single-pad method for hand soldering.\nORANGE Resistor goes on the RIGHT side.\nBLUE Resistor goes on the LEFT side.\n• Solder the 4x 2-Position headers.\n• For a better lighting effect, you can use HOT GLUE to cover the LEDs and the\nunmasked area on the back of the Minibadge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Sponsor", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "This badge can be acquired from the great folks at the Arctic Wolf sponsor booth, or in other ways they see fit to distribute them.", "rarity": "Common", "timestamp": "" }, { "title": "CHECKPOINT MINIBADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/checkpoint-minibadge-front.png", "backImageUrl": "images/2022/checkpoint-minibadge-back.png", "description": "Checkpoint is one of our 2022 Sponsors, and they elected to\nhave is design and build them a Minibadge to show off their new\nlogo design.\nYou can obtain this MiniBadge by visiting the Checkpoint\nSponsor Booth and interacting with their staff.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LED first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 3x 2-Position headers.\n• For a better lighting effect, you can use HOT GLUE to cover the LEDs and the\nunmasked area on the back of the Minibadge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Sponsor", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Common", "timestamp": "" }, { "title": "COMPUNET MINIBADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/compunet-minibadge-front.png", "backImageUrl": "images/2022/compunet-minibadge-back.png", "description": "Compunet is one of our 2022 Sponsors.\nYou can obtain this MiniBadge by visiting the Compunet Sponsor\nBooth and interacting with their staff.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Sponsor", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Common", "timestamp": "" }, { "title": "UETN SPONSOR BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/uetn-sponsor-badge-front.png", "backImageUrl": "images/2022/uetn-sponsor-badge-back.png", "description": "UETN is SAINTCON’s longest supporting sponsor. This\norganization was part of the initial founding of SAINTCON many\nyears ago. Jup1t3r is a proud employee of this great organization\nwhich serves the public education, state government, and rural\ntele-health systems.\nYou can obtain this badge by finding a UETN employee and\ninteracting with them.", "specialInstructions": "", "solderingInstructions": "• Begin on the FRONT side first.\n• LED Direction indicators are on the image above. They are also noted as a small\nDOT on the circuit-board itself.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor on the back using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Sponsor", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Rare", "timestamp": "" }, { "title": "VALCOM SPONSOR BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/valcom-sponsor-badge-front.png", "backImageUrl": "images/2022/valcom-sponsor-badge-back.png", "description": "Valcom (“VLCM”) is SAINTCON’s UBER sponsor for 2022, and\nwe could not be more excited to have them partner with us at this\nlevel. Their Minibadge design is of a rabid ferret, which is\nValcom’s Cybersecurity mascot.\nLED ORIENTATION WARNING\nNOTE: This LED has poor markings for\npolarity. Please reference the image\nabove to ensure you have the LED\ninstalled the right direction.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder either the BLINK or SOLID size of the Jumper depending on your\npreference.\nBAD\nNO BLINK SOLID\nJUMPER JUMPER JUMPER JUMPER\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Sponsor", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these MiniBadges, please visit the Valcom booth in the expo center.", "rarity": "Common", "timestamp": "" }, { "title": "Utah State University", "author": "Ay.Aitch", "profilePictureUrl": "", "frontImageUrl": "images/2022/utah-state-university-front.png", "backImageUrl": "images/2022/utah-state-university-back.png", "description": "SAINTCon is a highlight for several USU employees to attend. Go\nAggies!\nThis is a trader minibadge for the USU attendees, you may be\nawarded one by trading other unique badges, wearing Aggie\ngear, or maybe even belting out a rendition of the Scotsman!", "specialInstructions": "", "solderingInstructions": "• Solder the LED with the cathode down\n• Solder on the resistor\n• Solder on the header pins\n• For a better lighting effect, you can use HOT GLUE to cover the LEDs and the\nunmasked area on the back of the Minibadge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Uncommon", "timestamp": "" }, { "title": "AH - Moto", "author": "Ay.Aitch", "profilePictureUrl": "", "frontImageUrl": "images/2022/ah-moto-front.png", "backImageUrl": "images/2022/ah-moto-back.png", "description": "This is one badge in a series of “things I like to do…”\nIf you also like riding motorcycles, especially dirt bikes on single\ntrack trails, hit me up and tell me a story, show me a pic, or trade\nme for another unique minibadge.", "specialInstructions": "", "solderingInstructions": "• Solder the LED as indicated in the picture\n• Solder on the resistor\n• Solder on the header pins", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Rare", "timestamp": "" }, { "title": "AH - campfire", "author": "Ay.Aitch", "profilePictureUrl": "", "frontImageUrl": "images/2022/ah-campfire-front.png", "backImageUrl": "images/2022/ah-campfire-back.png", "description": "This is another badge in a series of “things I like to do…”. It\nfeatures a flickering LED that will hopefully look like a campfire\nburning when lit.\nIf you also like camping, being outdoors, making smores, and\nsuch, hit me up and tell me a story, show me an outdoor pic, or\ntrade me for another unique minibadge.", "specialInstructions": "", "solderingInstructions": "• Solder the LED as indicated in the picture, leave the lead wires long enough to\nbend the LED over to be in the middle of the badge, like this:\n• Solder on the resistor\n• Solder on the header pins", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Rare", "timestamp": "" }, { "title": "BEAR JUMP BADGE", "author": "B3rJmp", "profilePictureUrl": "", "frontImageUrl": "images/2022/bear-jump-badge-front.png", "backImageUrl": "images/2022/bear-jump-badge-back.png", "description": "Find B3rJmp for one of these.", "specialInstructions": "", "solderingInstructions": "• Start on the Back of the Circuit Board\n• Solder the Resistors using a single-pad soldering method. They are small, so it’s\neasier to start with them first.\n• Solder the LEDs using the single-pad soldering method. See the diagram above\nto ensure you use proper orientation.\n• Solder the 4x 2-Position headers.\n• For a better lighting effect, you can use HOT GLUE to cover the LEDs and the\nunmasked area on the back of the Minibadge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "Find B3rJmp for one of these.", "rarity": "Super Rare", "timestamp": "" }, { "title": "BABY YODA BADGE", "author": "Mr. & Mrs bfcoder", "profilePictureUrl": "", "frontImageUrl": "images/2022/baby-yoda-badge-front.png", "backImageUrl": "images/2022/baby-yoda-badge-back.png", "description": "Baby Yoda eating a cookie and barfing.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED direction indicators are on the image above.\n• Solder the resistor first, using the single-pad method for hand soldering.\n• Solder the LED’s using the single-pad method for hand soldering.\n• Bridge the Jumper to either make it Blink or Solid illumination.\n• Solder the 3x 2-position headers.\nBAD\nNO BLINK SOLID\nJUMPER JUMPER JUMPER JUMPER", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this MiniBadge, trade with bfcoder.", "rarity": "Rare", "timestamp": "" }, { "title": "BAT SYMBOL aND SIGNAL", "author": "bfcoder", "profilePictureUrl": "", "frontImageUrl": "images/2022/bat-symbol-and-signal-front.png", "backImageUrl": "images/2022/bat-symbol-and-signal-back.png", "description": "These are two separate badges, with a similar design and\nassembly method, so they are included together here.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED direction indicators are on the image above.\n• Solder the resistor first, using the single-pad method\nfor hand soldering.\n• Solder the LED’s using the single-pad method for\nhand soldering.\n• Solder either the BLINK or SOLID set of the Jumper\ndepending on your preference.\nBAD\nNO BLINK SOLID\nJUMPER JUMPER JUMPER JUMPER", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this MiniBadge, trade with bfcoder.", "rarity": "Very Rare", "timestamp": "" }, { "title": "HORSE HOOF BADGE", "author": "bfcoder", "profilePictureUrl": "", "frontImageUrl": "images/2022/horse-hoof-badge-front.png", "backImageUrl": "images/2022/horse-hoof-badge-back.png", "description": "This is the barefoot horse hoof badge, by bfcoder. You will have\nto ask him what it’s all about.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED direction indicators are on the image above.\n• Solder the resistor first, using the single-pad method for hand soldering.\n• Solder the LED’s using the single-pad method for hand soldering.\n• Bridge the Jumper to either make it Blink or Solid illumination.\n• Solder the 4x 2-position headers.\nBAD\nNO BLINK SOLID\nJUMPER JUMPER JUMPER JUMPER", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this MiniBadge, trade with bfcoder.", "rarity": "Very Rare", "timestamp": "" }, { "title": "PORTAL 2 BADGE", "author": "bfcoder", "profilePictureUrl": "", "frontImageUrl": "images/2022/portal-2-badge-front.png", "backImageUrl": "images/2022/portal-2-badge-back.png", "description": "This Portal 2 Fandom badge comes in two versions, One with\nsolid lights, and one that blinks.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED direction indicators are on the image above.\n• Solder the resistor first, using the single-pad method\nfor hand soldering.\n• Each resistor is paired with the color of LED. The\npairing matters!\n• Solder the 5.1ohm on the left side with the blue LED.\n• Solder the 68ohm on the right side with the orange\nLED.\n• Solder the LED’s using the single-pad method for\nhand soldering.\n• Solder the 4x 2-position headers.\n• For a better lighting effect, you can use HOT GLUE to\ncover the LEDs and the unmasked area on the back of\nthe Minibadge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these minibadges, come trade with me.", "rarity": "Rare", "timestamp": "" }, { "title": "SAINT KHAN BADGE", "author": "bfcoder", "profilePictureUrl": "", "frontImageUrl": "images/2022/saint-khan-badge-front.png", "backImageUrl": "images/2022/saint-khan-badge-back.png", "description": "Khan from Star Trek, but with a Halo. Hence, Saint Khan.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED direction indicators are on the image above.\n• Solder the resistor first, using the single-pad method for hand soldering.\n• Solder the LED’s using the single-pad method for hand soldering.\n• Solder the 4x 2-position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this MiniBadge, come trade with me.", "rarity": "Very Rare", "timestamp": "" }, { "title": "UTAH HOME LABS BADGE", "author": "bfcoder & klipper & v0rtex", "profilePictureUrl": "", "frontImageUrl": "images/2022/utah-home-labs-badge-front.png", "backImageUrl": "images/2022/utah-home-labs-badge-back.png", "description": "This is the UHL Group Minibadge.\nWe will be selling these for donations to UHL at the HomeLabs\nCommunity Booth.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED direction indicators are on the image above.\n• Solder the resistor first, using the single-pad method for hand soldering.\n• Solder the LED’s using the single-pad method for hand soldering.\n• Solder the 4x 2-position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Uncommon", "timestamp": "" }, { "title": "UVU Minibadge", "author": "Brian Peterson", "profilePictureUrl": "", "frontImageUrl": "images/2022/uvu-minibadge-front.png", "backImageUrl": "images/2022/uvu-minibadge-back.png", "description": "Go Wolverines!\nThe UVU Minibadge shows the pride of that school.", "specialInstructions": "", "solderingInstructions": "• Start on the back side first\n• Solder the LED first, use the single-pad soldering method.\n• Solder the Resistor, orientation doesn’t matter\n• Solder the Pin Headers, you may need to cut one in half to fit on the bottom.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these MiniBadges, find one of the UVU folks, and either trade or social-engineer one of these.", "rarity": "Uncommon", "timestamp": "" }, { "title": "COMPUKIDMIKE Badge", "author": "CompuKidMike", "profilePictureUrl": "", "frontImageUrl": "images/2022/compukidmike-badge-front.png", "backImageUrl": "images/2022/compukidmike-badge-back.png", "description": "CompuKidMike never disappoints, as a premiere badge designer,\nwith several years designing the SAINTCON badge, but also now\na multi-year designer of the DEF CON badge.", "specialInstructions": "", "solderingInstructions": "• Badge will be pre-assembled except for:\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this MiniBadge, interact with CompuKidMike at either the BadgeLife Community, or in other areas of the conference.", "rarity": "Common", "timestamp": "" }, { "title": "HONKI Badge", "author": "C0n4rt15t & CompuKidMike", "profilePictureUrl": "", "frontImageUrl": "images/2022/honki-badge-front.png", "backImageUrl": "images/2022/honki-badge-back.png", "description": "When you hear it, you will know. We LOVE to make it Honk!", "specialInstructions": "", "solderingInstructions": "• This badge will be mostly pre-assembled\n• Solder the SW on the top side.\n• Solder the Speaker on the bottom side.\n• Attach the speaker with double-sided tape.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these bad boys, you will need to interact with Honki.", "rarity": "Rare", "timestamp": "" }, { "title": "RAY-MAN Badge", "author": "CompuKidMike & Ray-Man", "profilePictureUrl": "", "frontImageUrl": "images/2022/ray-man-badge-front.png", "backImageUrl": "images/2022/ray-man-badge-back.png", "description": "When you hear it, you will know. We LOVE to make it Honk!", "specialInstructions": "", "solderingInstructions": "• This badge will be mostly pre-assembled\n• Solder the SW on the top side.\n• Solder the Speaker on the bottom side.\n• Attach the speaker with double-sided tape.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these bad boys, you will need to interact with Honki.", "rarity": "Rare", "timestamp": "" }, { "title": "TWSS Badge", "author": "Berly & Katie & Lynsey", "profilePictureUrl": "", "frontImageUrl": "images/2022/twss-badge-front.png", "backImageUrl": "images/2022/twss-badge-back.png", "description": "For you Office fans, this is one of the iconic badges you need to\ncollect.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• Solder the resistors, using the single-pad method for hand soldering.\n• On the Front:\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this badge, interact with one of the designers listed above.", "rarity": "Rare", "timestamp": "" }, { "title": "BERLY MINIBADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/berly-minibadge-front.png", "backImageUrl": "images/2022/berly-minibadge-back.png", "description": "Berly is the spouse of Jup1t3r, and she had the best idea for a\nUNO reverse-card MiniBadge, so we built it together.\nIt features two LEDs, that can be configured to either stay on\nsolid, or blink off and on.\nObtaining this MiniBadge will require you to interact in a positive\nway with Berly as she makes her way around the conference.", "specialInstructions": "", "solderingInstructions": "• Begin on the back side first.\n• LED Direction indicators are on the image above.\n• Solder the two LEDs first, using the single-pad method for hand soldering.\n• Solder the Resistor using the same single-pad method for hand soldering.\n• Solder the Jumper at the bottom of the board, bridging EITHER the SOLID or\nBLINK side, Never Solder across all three.\nBAD\nNO BLINK SOLID\nJUMPER JUMPER JUMPER JUMPER\n• Solder the 3x 2-Position headers. Cut one in Half to use in the 1-pin corners.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Uncommon", "timestamp": "" }, { "title": "CHUNK BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/chunk-badge-front.png", "backImageUrl": "images/2022/chunk-badge-back.png", "description": "The Chunk Minibadge is our homage to our favorite @Chunk. It’s\ngreat to have him back and involved with SAINTCON.\nThis badge features a vibrating motor to make the “Truffle\nShuffle” effect complete.", "specialInstructions": "", "solderingInstructions": "• Start on the back side.\n• Solder the LED using the single-pad soldering method. Orient the LED so that\nthe green marker lines up with the diagram above.\n• Solder the resistor using the single-pad soldering method.\n• Next attach the Motor (If included) using the foam sticker already attached.\n• Cross the wires so that the RED wire goes through the POSITIVE motor hole.\n— Carefully strip the wire so that you can solder it to the appropriate hole.\n• Turn the badge over, and solder the switch using the single-pad soldering\nmethod.\n• Attach the four 2-position pin headers", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this Minibadge, interact with Chunk!", "rarity": "Rare", "timestamp": "" }, { "title": "CODEXICON BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/codexicon-badge-front.png", "backImageUrl": "images/2022/codexicon-badge-back.png", "description": "Personal Badge built by Jup1t3r for his son @codexicon.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this badge, you will need to interact with Codexicon.", "rarity": "Rare", "timestamp": "" }, { "title": "EDUROAM MINIBADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/eduroam-minibadge-front.png", "backImageUrl": "images/2022/eduroam-minibadge-back.png", "description": "EDUROAM is a consortium of education networks that work\ntogether to provide federated WiFi access across campuses\nthroughout the world.", "specialInstructions": "", "solderingInstructions": "• Begin on the Front side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Turn the badge over and solder the resistors.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "You can acquire this MiniBadge by interacting with a UETN employee who helps administer this program within the State of Utah.", "rarity": "Rare", "timestamp": "" }, { "title": "GADSEN FLAG BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/gadsen-flag-badge-front.png", "backImageUrl": "images/2022/gadsen-flag-badge-back.png", "description": "The Gadsen Flag badge is the badge from 2021 which is back in\na small run for 2022. Originally created to give to people who felt\noppressed by the mask mandate of 2021, this was a beautiful\nbadge I have grown to love.", "specialInstructions": "", "solderingInstructions": "• Start on the back side.\n• Solder the LEDs using the single-pad soldering method. Orient the LED so that\nthe green marker lines up with the diagram above.\n• Solder the resistor using the single-pad soldering method.\n• Attach the three 2-position headers", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this badge: Get one from @Jup1t3r while they last.", "rarity": "Rare", "timestamp": "" }, { "title": "I SEE YOU BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/i-see-you-badge-front.png", "backImageUrl": "images/2022/i-see-you-badge-back.png", "description": "Personal Badge built by Jup1t3r for his nephew VIP.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this badge, you will need to interact with VIP.", "rarity": "Rare", "timestamp": "" }, { "title": "LilMissZ BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/lilmissz-badge-front.png", "backImageUrl": "images/2022/lilmissz-badge-back.png", "description": "Designed for @LilMissZ, and because her favorite place is Arches\nNational Park! This badge features Delicate Arch, a Utah Icon!", "specialInstructions": "", "solderingInstructions": "• Start on the back side.\n• Solder the LEDs using the single-pad soldering method. Orient the LED so that\nthe green marker lines up with the diagram above.\n• Solder the resistor using the single-pad soldering method.\n• Attach the two 2-position headers", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this Minibadge, find @LilMissZ and trade.", "rarity": "Rare", "timestamp": "" }, { "title": "MACHETE BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/machete-badge-front.png", "backImageUrl": "images/2022/machete-badge-back.png", "description": "The Machete badge is the personal badge for @sirashrum.", "specialInstructions": "", "solderingInstructions": "• Start on the back side.\n• Solder the LEDs using the single-pad soldering method. Orient the LED so that\nthe green marker lines up with the diagram above.\n• Solder the resistor using the single-pad soldering method.\n• Attach the three 2-position headers", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this badge: • Find and meet @sirashrum • Tell him an embarrassing story • Tell him how you got your handle • Do Both of the above", "rarity": "Rare", "timestamp": "" }, { "title": "PORTAL BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/portal-badge-front.png", "backImageUrl": "images/2022/portal-badge-back.png", "description": "Being a fan of the Portal Games, Jup1t3r has built a fan\nMinibadge for the other Portal Fans out there.\nThis is a two-badge set. One Features ORANGE backlight, and\nthe other one features BLUE backlight.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the images to the left.\n• Solder the LEDs first, using the single-pad method for\nhand soldering. Do not Mix LED colors between\nbadges.\n• Solder the resistor using the single-pad method for\nhand soldering.\n• Solder the 4x 2-Position headers.\n• For a better lighting effect, you can use HOT GLUE to\ncover the LEDs and the unmasked area on the back of\nthe Minibadge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this MiniBadge set find Jup1t3r and interact with him. It’s preferred that you interact with him while at the BadgeLife Community Booth.", "rarity": "Rare", "timestamp": "" }, { "title": "Radiation MINIBADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/radiation-minibadge-front.png", "backImageUrl": "images/2022/radiation-minibadge-back.png", "description": "This is a re-run from 2021, and back by popular demand.", "specialInstructions": "", "solderingInstructions": "• Begin on the BACK side first.\n• LED Direction indicator is on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder each of the 3 resistors\n• Solder the Jumper using a pattern outlined below.\n• Solder the 4x 2-Position headers.\nBAD\nNO BLINK SOLID\nJUMPER JUMPER JUMPER JUMPER", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get on of these Minibadges, see Jup1t3r before he runs out of them.", "rarity": "Rare", "timestamp": "" }, { "title": "SRT BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/srt-badge-front.png", "backImageUrl": "images/2022/srt-badge-back.png", "description": "Personal Badge built by Jup1t3r for his nephew SQUATCH.\nSRT is: Sasquatch Research Team", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers.\n• For a better lighting effect, you can use HOT GLUE to cover the LEDs and the\nunmasked area on the back of the Minibadge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this badge, you will need to interact with Squatch.", "rarity": "Rare", "timestamp": "" }, { "title": "TOR BADGE", "author": "SJ", "profilePictureUrl": "", "frontImageUrl": "images/2022/tor-badge-front.png", "backImageUrl": "images/2022/tor-badge-back.png", "description": "The Onion Router (TOR), more commonly known as the Dark\nWeb. This badge is designed by @SJ.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistor using the single-pad method for hand soldering.\n• Add Solder to bridge either the BLINK or SOLID jumper (SEE BELOW)\n• Solder the 4x 2-Position headers.\n• For a better lighting effect, you can use HOT GLUE to cover the LEDs and the\nunmasked area on the back of the Minibadge.\nBAD\nNO BLINK SOLID\nJUMPER JUMPER JUMPER JUMPER", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this badge, you will need to find, and interact with @SJ", "rarity": "Uncommon", "timestamp": "" }, { "title": "VADER BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/vader-badge-front.png", "backImageUrl": "images/2022/vader-badge-back.png", "description": "The Darth Vader Minibadge is the one that will be super-rare. Not\nvery many exist, and they are intended to be for Jup1t3r to give\nto people who have made significant contributions to the\nconference. So if you see someone wearing this one around, you\ncan safely thank them for working Hard to make SAINTCON a\nsuccess.\nThis Minibadge is NOT in general circulation. Please don’t ask\nJup1t3r for one.", "specialInstructions": "", "solderingInstructions": "• Please watch the Online Video on how to assemble\nthis MiniBadge.\n• Video can be found here.", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Super Rare", "timestamp": "" }, { "title": "YODA BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2022/yoda-badge-front.png", "backImageUrl": "images/2022/yoda-badge-back.png", "description": "One of my coolest ideas for a MiniBadge to date. When I saw the\nLED filament technology, it just screamed lightsaber to me. Im\nproud to bring Yoda to SAINTCON this year.", "specialInstructions": "", "solderingInstructions": "• Please watch the Online Video on how to assemble\nthis MiniBadge.\n• Video can be found here.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get a Yoda Minibadge, you will have to find Jup1t3r and trade a MiniBadge, or introduce yourself and tell him what you like or dislike about SAINTCON While supplies last of course.", "rarity": "Uncommon", "timestamp": "" }, { "title": "Clue Dice", "author": "Professor Plum", "profilePictureUrl": "", "frontImageUrl": "images/2022/clue-dice-front.png", "backImageUrl": "images/2022/clue-dice-back.png", "description": "Simple D6 roller, press the side button for a new roll.", "specialInstructions": "", "solderingInstructions": "• Solder the 7 LEDs first\n• Flip the badge over and solder The 10 leg resistor, orientation doesn’t matter\n• Solder the ATTiny next, pin 1 is marked with the small circle, it should be nearest\nto the button.\n• Solder the Botton and then the header row.\n•THIS BADGE NEEDS PROGRAMMING\nOnce the soldering is complete visit the HHC to program the ATTiny", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "Obtainable from Professor Plum via trading", "rarity": "Super Rare", "timestamp": "" }, { "title": "U of U", "author": "Professor Plum", "profilePictureUrl": "", "frontImageUrl": "images/2022/u-of-u-front.png", "backImageUrl": "images/2022/u-of-u-back.png", "description": "Go Utes!", "specialInstructions": "", "solderingInstructions": "• Solder the LED first\n• Solder the resister, orientation doesn’t matter\n• Solder the 3x 2-pin headers", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one, find Professor Plum and show your support for the University of Utah", "rarity": "Uncommon", "timestamp": "" }, { "title": "Killer Whale Badge", "author": "Z2Orca", "profilePictureUrl": "", "frontImageUrl": "images/2022/killer-whale-badge-front.png", "backImageUrl": "images/2022/killer-whale-badge-back.png", "description": "This MiniBadge was designed as a personal icon by a first-time\nbadge maker and first-time SAINTCON attendee. It is\nrepresentative of his namesake handle, the Killer Whale.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are the green dots on the image above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistors next, using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers, with the Killer Whale art facing out.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these MiniBadges, you will need to talk with him and share a bit of knowledge about what you do, know, or love.", "rarity": "Rare", "timestamp": "" }, { "title": "DragonFly", "author": "Z1Dragonfly", "profilePictureUrl": "", "frontImageUrl": "images/2022/dragonfly-front.png", "backImageUrl": "images/2022/dragonfly-back.png", "description": "This MiniBadge was designed as a personal icon for a first-time\nSAINTCON attendee and life-long hacker. It is representative of\nher namesake handle, the Dragonfly. She is a passionate learner\nand inquisitive soul.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are the white dots on the badge, or green dots on the\nimage above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistors next, using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers, with the Dragon Fly and Flower art facing out.\n• For a better lighting effect, you can use HOT GLUE to cover the LEDs and the\nunmasked area on the back of the Minibadge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these MiniBadges, you will need to talk with her and help her level up in the quest for knowledge.", "rarity": "Rare", "timestamp": "" }, { "title": "UniKitty", "author": "Z3Thunder", "profilePictureUrl": "", "frontImageUrl": "images/2022/unikitty-front.png", "backImageUrl": "images/2022/unikitty-back.png", "description": "This MiniBadge was designed as a personal icon for my daughter,\nlover of Unicorns and Kitty whisperer. This one just happens to\nbe riding a lightning bolt.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are the white dots on the badge, or green dots on the\nimage above.\n• Solder the LEDs first, using the single-pad method for hand soldering.\n• Solder the resistors next, using the single-pad method for hand soldering.\n• Solder the 4x 2-Position headers, with the Text side facing out.\n• For a better lighting effect, you can use HOT GLUE to cover the LEDs and the\nunmasked area on the back of the Minibadge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these MiniBadges, just ask her for one, she’d especially love to trade.", "rarity": "Rare", "timestamp": "" }, { "title": "( )", "author": "Zevlag", "profilePictureUrl": "", "frontImageUrl": "", "backImageUrl": "", "description": "You’ve just acquired A LOT of parts. 20 to be exact. I hope you\nhave lots of fun assembling this badge. It has a micro motor\nmounted to the PCB that will spin with a custom 3D-printed fan\nblade designed by my son. There is also a jumper with cap that\ncan be used to turn off the motor, but leave the LEDs on.\nI’ve arranged the LEDs on the image to the left in the pattern that\nlooks best. I’m sorry about the two smaller 0603 size LEDs, that’s\nwhat happens when you accidentally order 4,000 from China!", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side. Be careful not to bust the motor off the PCB. If needed, a very careful\ndrop of super glue will reattach firmly it after you finish assembly.\n• Solder the 5 LEDs first, according to the pattern indicated above.\n• To have the color properly illuminate the badge, the LEDs need to be soldered upside\ndown, with the clear part facing the board, and the orientation arrow showing towards\nyou.\n• All LEDs orient with the cathode toward the center.\n• Solder the 6 resistors next, using the single-pad method for hand soldering.\n• Solder motor wires to the pads at the top, near R6. Just put a bit of solder on the pad, then put\nthe wire end in it, holding the wire in place while the solder cools.\n• Solder the SMD 2 pin header to J1. This is easiest done using the single-pad method for hand\nsoldering, and tweezer to hold the pins in place. Place the cap on both pins when done, this is\nthe “ON” position. “OFF” is with the cap on 1 pin.\n• Solder the 4x 2-Position headers, with the Blown Away art facing out.\n• Locate the hole in the center of one side of the blade and while holding the bottom of the motor\nCarefully push the fan blade onto the motor shaft.", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these MiniBadges, find Zevlag and convince him to give you one (bribes work).", "rarity": "Rare", "timestamp": "" }, { "title": "Lego Badge", "author": "Zevlag", "profilePictureUrl": "", "frontImageUrl": "images/2022/lego-badge-front.png", "backImageUrl": "images/2022/lego-badge-back.png", "description": "The iconic DIY project, everybody’s favorite brick, Lego! This\nminibadge sports the design of a 2x2 Plate for attaching your\nfavorite (mini) builds.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• Solder the two resistors, using the single-pad method for hand soldering.\n• On the front, solder the two LEDs, upside down.\n• This badge is best experienced with the LEDs soldered upside down, with the\nclear part facing the board, and the orientation arrow pointing out.\n• This requires a slightly larger blob of solder on both ends.\n• Solder the 4x 2-Position headers, with the Lego art facing out.\n• (Optional) For an awesome experience, and to attach Lego’s to your minibadge, a\ndrop of Kragle (any fast drying super glue) will work to simply attach a lego plate\n(not included).", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these MiniBadges, find Zevlag and convince him to give you one (bribes work).", "rarity": "Rare", "timestamp": "" }, { "title": "Lego Badge with mini-figURE", "author": "Zevlag", "profilePictureUrl": "", "frontImageUrl": "images/2022/lego-badge-with-mini-figure-front.png", "backImageUrl": "images/2022/lego-badge-with-mini-figure-back.png", "description": "The iconic DIY project, everybody’s favorite brick, Lego! This\nminibadge sports a 2x2 Plate for attaching your favorite (mini)\nbuilds.\nWhat’s better than a minibadge? A minifig! You have been lucky\nenough to receive a custom painted Hackers Challenge themed\nminifig to adorn your Lego minibadge.", "specialInstructions": "", "solderingInstructions": "• Follow the instructions on the previous page for “Lego Badge”.\n• Follow the minifig assembly instructions below.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these MiniBadges, you’ll need to have made significant contributions to Hackers Challenge this year.", "rarity": "Super Rare", "timestamp": "" }, { "title": "Poolcon", "author": "Zevlag", "profilePictureUrl": "", "frontImageUrl": "images/2022/poolcon-front.png", "backImageUrl": "images/2022/poolcon-back.png", "description": "Poolcon is an informal event for SAINTCON Committee and Staff\nto wind down, debrief and relax. Friendships are made, problems\nare solved, and awesome stuff is planned for attendees.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicator is on the image above.\n• Solder the LED first, using the single-pad method for hand soldering.\n• To properly illuminate the acrylic, it should be soldered standing on its side,\npointing into the plastic.\n• This requires a slightly larger blob of solder on both ends.\n• I’m sorry for the 0603 LED, that’s what happens when I get 4,000 from China.\n• Solder the resistors next, using the single-pad method for hand soldering.\n• Solder the 2x 2-Position headers, with the SAINTCON art facing out.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these MiniBadges you need to be SAINTCON Committee, Staff, or Volunteer and talk to Zevlag and commit to contribute to the “2022 Lessons Learned” document.", "rarity": "Rare", "timestamp": "" }, { "title": "Minnie Badge", "author": "T. Zevlag", "profilePictureUrl": "", "frontImageUrl": "images/2022/minnie-badge-front.png", "backImageUrl": "images/2022/minnie-badge-back.png", "description": "This minibadge is a “Minnie Badge”.\nThere are two color variations available.\nNOTE: This badge has a minor Cosmetic Flaw! The\nsilver dot marks the anode side of the LED’s. Use\nthe GREEN dot on this image as orientation\nreference for cathode.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image and note\nabove.\n• Solder the 2 LEDs first, using the single-pad method\nfor hand soldering.\n• Solder the 2 resistors next, using the single-pad\nmethod for hand soldering.\n• Solder the 4x 2-Position headers, with the Minnie Bow\nart facing out.\n• For the best illumination effect cover the back,\nincluding LEDs with hot glue.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these MiniBadges, you must find T. Zevlag and convince her to give you one.", "rarity": "Rare", "timestamp": "" }, { "title": "RAY-MAN 2022", "author": "Ray-Man", "profilePictureUrl": "", "frontImageUrl": "images/2022/ray-man-2022-front.png", "backImageUrl": "images/2022/ray-man-2022-back.png", "description": "This was my first attempt to create my own MiniBadge, I\nappreciate others that offered to do this for me, but were willing\nto take double the time in helping answer questions. So thank\nyou Jup1t3r and others for answering my questions and double\nchecking my work. It was much appreciated! I hope everyone that\ngets my badge has as much fun building it as I did creating it!\nIf you want my MiniBadge please find Ray-Man while wondering\nthe con. We can exchange how we each got our handles,\nwhether you came up with it yourself, or if you were “given” it by\na mentor.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first (the components in the middle of the badge), using the\nsingle-pad method for hand soldering.\n• Solder the resistors (the components on the left) using the single-pad method for\nhand soldering.\n• Solder the 4x 2-Position headers.\n• For a better lighting effect, you can use HOT GLUE to cover the LEDs and the\nunmasked area on the back of the Minibadge.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Rare", "timestamp": "" }, { "title": "KITT BADGE", "author": "Sh33pr0ck", "profilePictureUrl": "", "frontImageUrl": "images/2022/kitt-badge-front.png", "backImageUrl": "images/2022/kitt-badge-back.png", "description": "KITT is a second run of my very first mini badge ever from 2018.\n6 total and only 2 available. Runs off an attiny85 and may or may\nnot already be prebuilt due to special circumstances i.e. because\nI crossed wires not knowing what I was doing. May have\ntraditional red lights or alternative green.\nEasy to assemble…see above.", "specialInstructions": "", "solderingInstructions": "• This badge is pre-assembled", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "Find me wandering around and probably working as a volunteer in the communities somewhere. Interesting trades accepted.", "rarity": "Super Rare", "timestamp": "" }, { "title": "DC435 BUS", "author": "Sh33pr0ck", "profilePictureUrl": "", "frontImageUrl": "images/2022/dc435-bus-front.png", "backImageUrl": "images/2022/dc435-bus-back.png", "description": "DC435 Bus 2022. Design by ay.aitch", "specialInstructions": "", "solderingInstructions": "• Solder the LED using the single-pad soldering method. See the LED Cathode\ndirection noted above.\n• Solder the Resistor using the single-pad soldering method.\n• Create a solder jumper on the left or right as seen below.\nBAD\nNO BLINK SOLID\nJUMPER JUMPER JUMPER JUMPER", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "Find someone from DC435 and talk to them about our monthly meetups.", "rarity": "Rare", "timestamp": "" }, { "title": "Hacker Skull", "author": "Sh33pr0ck", "profilePictureUrl": "", "frontImageUrl": "images/2022/hacker-skull-front.png", "backImageUrl": "images/2022/hacker-skull-back.png", "description": "Pretty much just a skull with red eyes.", "specialInstructions": "", "solderingInstructions": "• Cathode towards green dot.\n• Bridge right two pads of JP1 for clock pin.\n• Bridge left two pads of JP1 for normal 3.3v.\nBAD\nNO BLINK SOLID\nJUMPER JUMPER JUMPER JUMPER", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "Find me wandering around. I’ll trade for something I don’t have.", "rarity": "Rare", "timestamp": "" }, { "title": "DC435 Ultra", "author": "Sh33pr0ck", "profilePictureUrl": "", "frontImageUrl": "images/2022/dc435-ultra-front.png", "backImageUrl": "images/2022/dc435-ultra-back.png", "description": "DC435 badge with Common Anode RGB LED powered by an\nATTiny841. Use the pad on the right to cycle colors and the pad\nto the left to cycle through messages preloaded and using i2c.\nMessages can be seen on previous years badges or anything\nelse capable of reading them. Use the ICSP to program it\nhowever you want.\nVery few available.", "specialInstructions": "", "solderingInstructions": "• RGB and ATTiny will be pre-installed as there are no extras and are fairly difficult\nto hand solder and have all colors function.\n• Resistor 106 goes to R4 and R5\n• Resistor 510 goes to R2\n• Resistor 1000 goes to R3\n• Resistor 1500 goes to R1\n• For programing yourself with ICSP use the following pins in Arduino:\n• Red = 2; Green = 3; Blue = 7; Right pad = 10; Left pad = 9\n• The pads are used as a traditional button.\n• ATTiny Core was used with Arduino.\n• Wire Mode: Slave Only and Pin Map: Counterclockwise (or the pins will be off)", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "Find me wandering around and trade something cool and unique.", "rarity": "Super Rare", "timestamp": "" }, { "title": "2022 TFHT Alternative", "author": "Sh33prock", "profilePictureUrl": "", "frontImageUrl": "images/2022/2022-tfht-alternative-front.png", "backImageUrl": "images/2022/2022-tfht-alternative-back.png", "description": "Alternative version to the TFHT minibadge. Built with inspiration\nfrom Mupp and Govna. Why wouldn’t aliens want to abduct\nSasquatch?\nTrade me something cool and unique. Very few available. Find me\nwandering around.", "specialInstructions": "", "solderingInstructions": "• Cathode towards the green dots.\n• Resistor 95R3 goes to R2.\n• Lay through hole LED towards the top with the LED over the “beam” of the\nspaceship (backside).\n• Solder into place and trim extra.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Super Rare", "timestamp": "" }, { "title": "Kali", "author": "Sh33pr0ck", "profilePictureUrl": "", "frontImageUrl": "images/2022/kali-front.png", "backImageUrl": "images/2022/kali-back.png", "description": "Inspired by Kali with credit to 2e08 and built by Sh33pr0ck.\nIntermediate only due to smaller part sizes.", "specialInstructions": "", "solderingInstructions": "• Cathode towards the green dot.\n• Bridge bottom two pads on JP1 for clock pin.\n• OR Bridge top two pads on JP1 for normal 3.3v.\n• For a better lighting effect, you can use HOT GLUE to cover the LEDs and the\nunmasked area on the back of the Minibadge.\nBAD\nNO BLINK SOLID\nJUMPER JUMPER JUMPER JUMPER", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "Find Sh33pr0ck or Nate and trade something unique.", "rarity": "Super Rare", "timestamp": "" }, { "title": "Zodiak BADGE", "author": "Zodiak", "profilePictureUrl": "", "frontImageUrl": "images/2022/zodiak-badge-front.png", "backImageUrl": "images/2022/zodiak-badge-back.png", "description": "I made a simple badge this year, but a lot of thought went into the\n“Z” design, or at least that’s the story i’m sticking to.", "specialInstructions": "", "solderingInstructions": "• Solder the LED using the single-pad soldering method.\n• Solder the Resistor using the single-pad soldering method.\n• Attach the four 2-position pin headers", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these badges, find me around the con.", "rarity": "Uncommon", "timestamp": "" }, { "title": "SPAMWIZARD BADGE", "author": "SpamWizard", "profilePictureUrl": "", "frontImageUrl": "images/2022/spamwizard-badge-front.png", "backImageUrl": "images/2022/spamwizard-badge-back.png", "description": "Designed by SpamWizard, the offspring of Zodiak.", "specialInstructions": "", "solderingInstructions": "• Solder the LEDs using the single-pad soldering method.\n• Solder the Resistors using the single-pad soldering method.\n• Attach the four 2-position pin headers", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "Find this kid, and beg for one?", "rarity": "Rare", "timestamp": "" }, { "title": "UniversalIndex BADGE", "author": "Zodiak", "profilePictureUrl": "", "frontImageUrl": "images/2022/universalindex-badge-front.png", "backImageUrl": "images/2022/universalindex-badge-back.png", "description": "Designed by Zodiak, for the UniversalIndex…. You get to figure\nout who that is.", "specialInstructions": "", "solderingInstructions": "• Solder the LED using the single-pad soldering method.\n• Solder the Resistor using the single-pad soldering method.\n• Attach the four 2-position pin headers", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "Find this kid, and beg for one?", "rarity": "Rare", "timestamp": "" }, { "title": "Phisheratu BADGE", "author": "DistinctM1nd", "profilePictureUrl": "", "frontImageUrl": "images/2022/phisheratu-badge-front.png", "backImageUrl": "images/2022/phisheratu-badge-back.png", "description": "Designed by DistinctM1nd.\nNo details were provided on how to acquire this MiniBadge.", "specialInstructions": "", "solderingInstructions": "• Start on the back\n• Solder the SMD LED using the single-pad soldering method.\n• Solder the Resistors using the single-pad soldering method.\n• On the Front Side: Attach the LED with the long-lead through the CIRCLE hole.\n• Attach the Pin Headers", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Rare", "timestamp": "" }, { "title": "CALL ME BADGE", "author": "DistinctM1nd", "profilePictureUrl": "", "frontImageUrl": "images/2022/call-me-badge-front.png", "backImageUrl": "images/2022/call-me-badge-back.png", "description": "Designed by DistinctM1nd.\nNo details were provided on how to acquire this MiniBadge.", "specialInstructions": "", "solderingInstructions": "• Start on the back\n• Solder the SMD LED using the single-pad soldering method.\n• Solder the Resistor using the single-pad soldering method.\n• On the Front Side: Attach the Selector using the extra Pin Headers provided.\n• Attach the 4x 2-position Pin Headers", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Rare", "timestamp": "" }, { "title": "DAVE TRAIN BADGE", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2022/dave-train-badge-front.png", "backImageUrl": "images/2022/dave-train-badge-back.png", "description": "To get this Minibadge, HollyHacker is interested in trading, but is\nalso interested in networking.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• Solder the Resistor first, using the single-pad soldering method.\n• Attach the LED from the BOTTOM. It will need enough length to be bent to point\nthe LED upward to backlight the board. LONG-LEG goes through the Circle hole.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this Minibadge, HollyHacker is interested in trading, but is also interested in networking.", "rarity": "Super Rare", "timestamp": "" }, { "title": "STAR TREK v1 Badge", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2022/star-trek-v1-badge-front.png", "backImageUrl": "images/2022/star-trek-v1-badge-back.png", "description": "From the Mind of SHIFTY, this minibadge shows how much of a\nfan of Star Trek SHIFTY is.", "specialInstructions": "", "solderingInstructions": "• Start on the back\n• Solder the SMD LED using the single-pad soldering method. See the LED\norientation mark above.\n• Solder the Resistor using the single-pad soldering method.\n• Attach the 4x 2-position Pin Headers", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these badges, please find SHIFTY and either trade or provide some type of “Bribe”", "rarity": "Super Rare", "timestamp": "" }, { "title": "STARFLEET SERIES Badge", "author": "SHIFTY", "profilePictureUrl": "", "frontImageUrl": "images/2022/starfleet-series-badge-front.png", "backImageUrl": "images/2022/starfleet-series-badge-back.png", "description": "The Starfleet series badge comes in several types with different\nfactions center emblems. There may even be one with an\nEnterprise emblem.", "specialInstructions": "", "solderingInstructions": "• Start on the BACK: Solder the SMD LED using the single-pad soldering method.\n• Solder the back Resistor using the single-pad soldering method.\n• Turn over to the FRONT: Solder the front Resistor using the single-pad soldering\nmethod.\n• Solder the front LED using the single-pad soldering method.\n• Use the extra header pins to attach the provided faction emblem.\n• Bridge the Jumper to either make it Blink or Solid illumination.\n• Attach the 4x 2-position Pin Headers\nBAD\nNO BLINK SOLID\nJUMPER JUMPER JUMPER JUMPER", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get one of these badges, find Ray-Man and convince him that you need to represent one of these factions.", "rarity": "Super Rare", "timestamp": "" }, { "title": "BoardinJunky", "author": "Ray-Man", "profilePictureUrl": "", "frontImageUrl": "images/2022/boardinjunky-front.png", "backImageUrl": "images/2022/boardinjunky-back.png", "description": "This MiniBadge was designed by Ray-Man. Ray-Man told\nBoardinJunky that as this was his first SAINTCON he needed\nsomething to force him to network with others within this great\ncommunity!", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first (the components on left-middle and bottom-center of the\nbadge), using the single-pad method for hand soldering.\n• Solder the resistors (the components right above bottom header pins) using the\nsingle-pad method for hand soldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get BoardinJunky’s MiniBadge please find him while wondering the con. Introduce yourself and your story on why you come to SAINTCON. (If you need help tracking down BoardinJunky, talk to Ray-Man, hopefully he can point you in the right direction.)", "rarity": "Rare", "timestamp": "" }, { "title": "Perry", "author": "Ray-Man", "profilePictureUrl": "", "frontImageUrl": "images/2022/perry-front.png", "backImageUrl": "images/2022/perry-back.png", "description": "This MiniBadge was designed\nexclusively the Family Night Event.\nIf you want this MiniBadge please find Ray-Man while wondering\nthe Family Night and tell him why you want/need one.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• LED Direction indicators are on the image above.\n• Solder the LEDs first (Labeled D1 & D2), using the single-pad method for hand\nsoldering.\n• Solder the resistors (Labeled R1 & R2) using the single-pad method for hand\nsoldering.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "", "rarity": "Rare", "timestamp": "" }, { "title": "CHECKING LOGS BADGE", "author": "Hollyhacker & RuShan", "profilePictureUrl": "", "frontImageUrl": "images/2022/checking-logs-badge-front.png", "backImageUrl": "images/2022/checking-logs-badge-back.png", "description": "To get this Minibadge, HollyHacker is interested in trading, but is\nalso interested in networking.", "specialInstructions": "", "solderingInstructions": "• Begin on the Back side first.\n• Solder the Resistor first, using the single-pad soldering method.\n• Attach the LED from the BOTTOM. It will need enough length to be bent to point\nthe LED upward to backlight the board. LONG-LEG goes through the Circle hole.\n• Solder the 4x 2-Position headers.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "Personal", "conferenceYear": "2022", "boardHouse": "", "howToAcquire": "To get this Minibadge, HollyHacker is interested in trading, but is also interested in networking.", "rarity": "Super Rare", "timestamp": "" } ]