[ { "title": "PEOPLE BADGES", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2021/people-badges-front.png", "backImageUrl": "images/2021/people-badges-back.png", "description": "", "specialInstructions": "", "solderingInstructions": "LEDs: Two LEDs (D1, D2) near center. Orient with the GREEN DOT toward the TOP of the board.\nResistor: Single resistor; no polarity.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "", "conferenceYear": "2021", "boardHouse": "", "howToAcquire": "", "rarity": "", "timestamp": "" }, { "title": "TIN FOIL HAT TALKS", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2021/tin-foil-hat-talks-front.png", "backImageUrl": "images/2021/tin-foil-hat-talks-back.png", "description": "", "specialInstructions": "", "solderingInstructions": "LEDs: Two LEDs (D1, D2). Orient with the GREEN DOT toward the BOTTOM of the board.\nResistor: Single resistor; no polarity.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "", "conferenceYear": "2021", "boardHouse": "", "howToAcquire": "", "rarity": "", "timestamp": "" }, { "title": "PRIVATE LTE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2021/private-lte-front.png", "backImageUrl": "", "description": "", "specialInstructions": "It is CRITICAL that you do not reverse this LED; it will blow it up.", "solderingInstructions": "LED: Single through-hole LED pressed through the large hole. Bend and trim leads to make contact with the D1 pads; match the upside-down layout shown. Ensure correct orientation (flat side as indicated).\nResistor: Single resistor; no polarity.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "", "conferenceYear": "2021", "boardHouse": "", "howToAcquire": "", "rarity": "", "timestamp": "" }, { "title": "RFID/NFC BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2021/rfidnfc-badge-front.png", "backImageUrl": "images/2021/rfidnfc-badge-back.png", "description": "", "specialInstructions": "If using the provided NFC sticker, trim headers flush so they don’t interfere.", "solderingInstructions": "LEDs: Two LEDs (D1, D2). Orient with the GREEN DOT toward the TOP of the board.\nResistor: Single resistor; no polarity.\nHeaders: Recommended to TRIM headers FLUSH with the top of the board; solder so only a small rounded solder blob remains on top.\nSticker: Center the NFC tag sticker on the top of the minibadge (may not be included in every one).", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "", "conferenceYear": "2021", "boardHouse": "", "howToAcquire": "", "rarity": "", "timestamp": "" }, { "title": "HACK IN THE BOX", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2021/hack-in-the-box-front.png", "backImageUrl": "images/2021/hack-in-the-box-back.png", "description": "", "specialInstructions": "", "solderingInstructions": "Inverter: Best soldered with hot air + solder paste. Dab a very small amount of paste on the 5 pads, place inverter in correct orientation, heat with hot air; add flux once paste starts to melt. Recommended hot air temp: 190°C.\nLEDs: Mount with the BUBBLE part in the drilled hole; when badge is facing up, the back of the LED should match the guide image. LEDs come in BLUE/GREEN pairs.\nResistors: Two resistors (GREEN and BLUE); place on the proper side. No polarity.", "solderingDifficulty": "Advanced", "quantityMade": 0, "category": "", "conferenceYear": "2021", "boardHouse": "", "howToAcquire": "", "rarity": "", "timestamp": "" }, { "title": "RED TEAM", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2021/red-team-front.png", "backImageUrl": "images/2021/red-team-back.png", "description": "", "specialInstructions": "IMPORTANT: Do NOT bridge all 3 jumper pads; it can short and cause issues with the entire badge.", "solderingInstructions": "LEDs: Three LEDs (D1, D2, D3). Orient GREEN DOT toward the BOTTOM and LEFT as shown.\nResistor: Single resistor; no polarity.\nJumper: Required. For BLINKING, solder middle+bottom pads. For SOLID ON, solder middle+top pads.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "", "conferenceYear": "2021", "boardHouse": "", "howToAcquire": "", "rarity": "", "timestamp": "" }, { "title": "HACKER CHALLENGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2021/hacker-challenge-front.png", "backImageUrl": "images/2021/hacker-challenge-back.png", "description": "", "specialInstructions": "EPROM programming can be done at the Hackers Challenge booth after soldering.", "solderingInstructions": "LEDs: Two LEDs on the front (marked D3 and D3 in the guide) oriented with GREEN mark to the LEFT. Recommended: BLUE LED on top and ORANGE LED on bottom on the front. One LED on the back (D1) oriented with GREEN near the top; if green on both sides, the side with TWO legs goes toward the top.\nResistors: Three resistors; place as shown and do not mix up values (680, 100, 100).\nEPROM: Very small; fits one way. Recommended solder paste + rework, but can be hand soldered. Inspect for bridges under magnification.", "solderingDifficulty": "Moderate", "quantityMade": 0, "category": "", "conferenceYear": "2021", "boardHouse": "", "howToAcquire": "", "rarity": "", "timestamp": "" }, { "title": "SCAVENGER HUNT", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2021/scavenger-hunt-front.png", "backImageUrl": "images/2021/scavenger-hunt-back.png", "description": "", "specialInstructions": "", "solderingInstructions": "LEDs: Two LEDs (D1, D2). Orient with the GREEN DOT toward the TOP of the board.\nResistor: Single resistor; no polarity.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "", "conferenceYear": "2021", "boardHouse": "", "howToAcquire": "", "rarity": "", "timestamp": "" }, { "title": "THE VAULT", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2021/the-vault-front.png", "backImageUrl": "images/2021/the-vault-back.png", "description": "", "specialInstructions": "", "solderingInstructions": "LEDs: Two LEDs (D1, D2). Orient with the GREEN DOT toward the TOP of the board.\nResistor: Single resistor; no polarity.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "", "conferenceYear": "2021", "boardHouse": "", "howToAcquire": "", "rarity": "", "timestamp": "" }, { "title": "STORE BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2021/store-badge-front.png", "backImageUrl": "images/2021/store-badge-back.png", "description": "", "specialInstructions": "IMPORTANT: Do NOT bridge all 3 jumper pads; it can short and cause issues with the entire badge.", "solderingInstructions": "LEDs: Two LEDs (D1, D2). Orient with the GREEN DOT toward the RIGHT of the board.\nResistor: Single resistor; no polarity.\nJumper: Required. For BLINKING, solder middle+bottom pads. For SOLID ON, solder middle+top pads.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "", "conferenceYear": "2021", "boardHouse": "", "howToAcquire": "", "rarity": "", "timestamp": "" }, { "title": "RADIATION BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2021/radiation-badge-front.png", "backImageUrl": "images/2021/radiation-badge-back.png", "description": "", "specialInstructions": "IMPORTANT: Do NOT bridge all 3 jumper pads; it can short and cause issues with the entire badge.", "solderingInstructions": "LEDs: Three LEDs mount with the light-emitting side toward the board. Align the TRIANGLE cutout on the LED to the matching shape on the board.\nResistors: Three identical resistors; any order and orientation.\nJumper: Required. For BLINKING, solder middle+top pads. For SOLID ON, solder middle+bottom pads.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "", "conferenceYear": "2021", "boardHouse": "", "howToAcquire": "", "rarity": "", "timestamp": "" }, { "title": "GADSEN FLAG", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2021/gadsen-flag-front.png", "backImageUrl": "images/2021/gadsen-flag-back.png", "description": "", "specialInstructions": "", "solderingInstructions": "LEDs: Two LEDs. Place with GREEN indicator DOWN and LEFT (per guide image).\nResistor: Single resistor; no polarity.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "", "conferenceYear": "2021", "boardHouse": "", "howToAcquire": "", "rarity": "", "timestamp": "" }, { "title": "MATRIX BADGE", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2021/matrix-badge-front.png", "backImageUrl": "images/2021/matrix-badge-back.png", "description": "", "specialInstructions": "CLOCK REQUIRED: must be connected to a badge with the Clock Pin enabled.", "solderingInstructions": "LEDs: Four LEDs (2 RED, 2 BLUE). Place in the right order and orientation. Orientation: RED LEDs have Green Indicator facing DOWN; BLUE LEDs have Green Indicator facing UP.\nResistors: Two resistors—one for RED LEDs and one for BLUE LEDs—match placement as indicated in the guide.", "solderingDifficulty": "Intermediate", "quantityMade": 0, "category": "", "conferenceYear": "2021", "boardHouse": "", "howToAcquire": "", "rarity": "", "timestamp": "" }, { "title": "USA FLAG", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2021/usa-flag-front.png", "backImageUrl": "images/2021/usa-flag-back.png", "description": "", "specialInstructions": "", "solderingInstructions": "LEDs: Two LEDs. Place with GREEN indicator DOWN and LEFT (per guide image).\nResistor: Single resistor; no polarity.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "", "conferenceYear": "2021", "boardHouse": "", "howToAcquire": "", "rarity": "", "timestamp": "" }, { "title": "COMPUNET", "author": "Jup1t3r", "profilePictureUrl": "", "frontImageUrl": "images/2021/compunet-front.png", "backImageUrl": "images/2021/compunet-back.png", "description": "", "specialInstructions": "", "solderingInstructions": "LEDs: Two LEDs (D1, D2). Orient with the GREEN DOT toward the TOP of the board.\nResistor: Single resistor; no polarity.", "solderingDifficulty": "Beginner", "quantityMade": 0, "category": "", "conferenceYear": "2021", "boardHouse": "", "howToAcquire": "", "rarity": "", "timestamp": "" } ]